Werbung
Verfügbare Sprachen
Verfügbare Sprachen
3. Important safety instructions:
WARNING: Basic safety precautions should be observed when handling this equipment to prevent injury, including the following advice: Read and follow all safety
instructions before and during the use of the device� Observe all important operating instructions and information when using the device� Otherwise the product may be
damaged or injuries occur�
DANGER: Special care should be taken to avoid possible electric shock when water is used in the operation of this appliance You should not attempt to repair the unit yourself, but return it
to an authorised service centre for repair or dispose of the unit� Do not use a device with a damaged power cable or if it does not work properly, has been dropped or otherwise damaged�
Drip loop: Make a so-called 'drip loop' (see illustration
This should be in the direction of the socket with each power cable� The ‚'drip loop' is the part of the power cord that is below the power outlet or connection
when an extension cord is used� This prevents water from running along the cable and coming into contact with the socket� Should the plug or plug socket get
wet, do NOT pull the plug� Switch off the fuse or circuit breaker for the device� Only then should you pull out the power cable and check the plug socket for
water�
Prevent injuries: Do not touch moving or hot parts to prevent personal injury�
Caution: Always separate the device from the power supply before you handle it, insert or remove parts or before devices are installed or maintained� Never pull
the power cable to pull the adapter out of the socket� Always hold and pull the plug connector� Always disconnect devices that are not in use from the power supply�
Never pick up the unit by the power cable�
Operating limitations: The device is not suitable for use by persons (including children) with reduced physical, sensory or mental abilities or by persons with little experience in handling
technical devices, unless these persons receive appropriate operating instructions before using the device or they are under the supervision of a person responsible for their safety� Children
should always be supervised to ensure that they do not play with the device�
Intended use: Use this device only for its intended purpose� The use of attachments not recommended or sold by the device manufacturer may lead to unsafe operating conditions�
Installation: Do not install or store the device where it is exposed to temperatures below freezing� Do not expose the unit to direct sunlight� Regularly check the device� Do not leave the
device unattended for a long period of time� Should an extension cable be required, ensure that the connection is water and dust proof� Only use a cable with a suitable power output� An
extension cord with lower amperage or wattage than the unit may overheat� Take care to route the extension cable so that you do not trip over it or pull it out� This appliance is intended
for household use only and not for commercial purposes�
4. Control unit and regulator unit:
1
Control unit
2
Display
3
LED activity indicator
4
Humidity sensor
5
Regulator unit
4.1 Control unit + Display:
The control unit
1
has a recess on the back� The control unit
The 1�5 meter cable length from the control unit
unit
1
to the humidity sensor
4
and switching states can be read quickly on the display
4.2 The control unit in detail:
The control unit
1
has an LED activity indicator
c)
d)
The sensor touch keys
,
and
a)
Humidification activity indicator
Dehumidification activity indicator
b)
Set key
c)
4.3 Display symbols:
∙ HSV: Humidity set value
∙ HDV: Humidification differential value
∙ DDV: Dehumidification differential value
∙ ADV: Alarm when the humidity exceeds or falls below the limit
(flashes and beeps when the humidity exceeds or falls below the limit)
4.4 Regulator unit:
The regulator unit
5
has 2 sockets� Socket 2 (Humidity
(Dehumidity
6
) is intended for the control of dehumidifiers such as exhaust fans� Each socket may be used for devices of up to a maximum of 600 W� The regulator unit
should be screwed to the inside of the wall or side wall of the base cabinet to prevent contact with the device in the event of water escaping from the terrarium�
5. Humidity sensor:
The Humidity Control II is equipped with a humidity sensor
Position the humidity sensor
4
in the terrarium far enough away from the humidifiers� This could otherwise lead to incorrect measurement or control values� Should the humidity
sensor
4
detect a break or sensor short circuit, this is indicated on the display
safety reasons� The humidity sensor
6. Basic functions:
Safety shutdown during programming: When using the programming mode, both plug sockets
Reset function: When no key is touched for 30 seconds in programming mode, the Humidity Control II automatically returns to operating mode�
Monitoring the functions of external devices: The control unit
regulation of external devices�
Backlighting: The Humidity Control II has automatic backlighting in programme mode� Backlighting automatically switches off after 30 seconds if no operation is performed�
Switch off signal tones: An acoustic alarm is deactivated by touching any key� The signal tone only sounds again when the programmed set value has been reached again before
another divergence occurs�
Measurement range: The setting range is: 20° % to 95° %� When these values are exceeded or not reached, this is indicated in the display
switch-on delay: To protect connected humidification systems, the Humidity Control II has an adjustable humidifier switch-on delay�
6
Tel.: +49 (0) 22 25 - 94 15 0 · Fax: +49 (0) 22 25 - 94 64 94 · info@dohse-aquaristik.de · www.hobby-terraristik.com
):
6
Socket 1 (Dehumidity)
7
Socket 2 (Humidity)
8
Cable connection
9
Screw set for wall mounting of the display
10
Suction cup for sensor mounting
1
is mounted on the wall or base cabinet using the screw set
1
to the regulator control unit
allow the control unit
1
to be positioned outside the terrarium base cabinet so that all values
2
�
3
for the heating and cooling operation�
e)
allow values to be set particularly easily�
Up key
d)
Down key
e)
7
) intended for controlling humidification systems such as irrigation systems or terrarium misters� Socket 1
4
� The humidity sensor
4
is a precision measuring instrument and can be easily replaced without calibration if necessary�
1
has an LED activity indicator
1
and 1�8 meter cable length from the control
∙ DD: Humidifier switch-on delay
∙
: Day mode
∙
: Night mode
∙
: Current time
4
is equipped with a quick-connect fastener and thus enables an easy installation of the sensor�
2
with --- and an alarm sound indicates the fault� External devices are switched off in this situation for
6
+
7
are switched off for safety�
3
for heating and cooling operation, with lights indicating the active
2
5
1
9
�
10
4
a)
b)
c)
d)
e)
2
with „HH" or „LL"� Humidifier
6
7
9
8
5
Werbung
