Herunterladen Diese Seite drucken
Verfügbare Sprachen

Verfügbare Sprachen

TM
Instructions for Providing a
Comfortable and Secure Fit
To size the Sure-Lock® ratchet headband:
1. Turn the ratchet knob counterclockwise until headband is
at largest size (Figure 1).
2. Place the helmet on your head and turn the ratchet knob
clockwise until headband is snug and comfortable.
To adjust helmet vertically:
1. Locate the vertical adjustment tabs at the front and back
of the headband. There are four tabs on the headband
and four black posts on the inner liner.
2. To raise or lower the headband, reposition the tabs on
the black posts and snap in place (Figure 2).
To raise or lower Faceshield:
1. Release tension knobs found on both sides of the
helmet.
2. Tighten knobs once faceshield is in desired position.
Firedome
®
FXE, PXE, RXE Helmet
Use
This product is only intended for use as described in this
manual.
Maintenance
Only original parts by the manufacturer may be used for
maintenance.
Cleaning and disinfecting
Remove ear/neck protector, headband, and crown
straps. Clean inner and outer shells with mild soap or
detergent. Wash the ear/neck protector, headband,
brow pad, and crown straps in warm, soapy water and
air dry at room temperature. Clean faceshields with mild
detergent, rinse thoroughly with clean water, and dry
with a soft cloth.
Figure 1
Do not use solvents or paint thinners on Firedome
helmets, as they could permanently mar surfaces or
degrade the protective properties of helmet
components. Touch-up painting on composite outer
shells can be done with Bullard-approved paints.
Failure to follow these instructions could reduce the
effectiveness of the helmet and result in death or
serious injury.
Storage
Wipe helmet and shield with anti-static cloth and store
in a cool, dry place where the helmet will be protected.
Transportation/Shipment
Helmet should be packaged in its original package to
ensure that it is protected from damage during transit.
Read all instructions and warnings before wearing
this helmet. Failure to follow these instructions could
Figure 2
cause death or serious injury.
User Manual
WARNING
WARNING
loading

Inhaltszusammenfassung für Bullard Firedome FXE

  • Seite 9: Pflege Und Wartung

    Anschläge. Außenschalen kann mit Farben ausgebessert 2. Verstellen Sie zum Heben oder Senken des Kopfbandes werden, die von der Firma Bullard zugelassen sind. die Reiter an den schwarzen Anschlägen und rasten diese Werden diese Hinweise nicht befolgt, könnte das ein (Abbildung 2).
  • Seite 10 Ersatzteile für den Helm der Typenreihe FXE, PXE und RXE FXE, Shell Shell Goggle R149 Nomex®-Kinnriemen mit Schnellöffnungsschnalle R960 Ersatz-Trageband-Innenausstattung für FXE, PXE und RXE Hierzu gehören ABS-Innenschale, Sure-Lock®-Ratschen- R150 Satz Montageteile für Gesichtsschutz kopfband, Schweißpolster, schlagfeste Auskleidung aus R310 4-Zoll-Polykarbonat-Gesichtsschutz für FXE, PXE Urethan, 6-Punkt-Tragebandausstattung aus Nylon und Schutzbrille für RXE (Visier als Option) Klettband (Ösen und Haken).
  • Seite 11 Artikeln, die innerhalb der Gewährleistungsfrist zurückgeschickt werden, unmittelbare Berührung mit Flammen oder geschmolzenem Metall und bei denen sich nach Kontrolle durch die Firma Bullard herausgestellt oder zum Schutz vor gefährlichen Chemikalien sowie biologischen hat, dass diese fehlerhaft sind. Dies Pflicht unterliegt folgenden oder radiologischen Mitteln bestimmt.

Diese Anleitung auch für:

Firedome pxeFiredome rxe