Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Timer Button
Setting a turn-off timer:
1.
Ensure the heater is plugged in, the power socket turned on,
and the on/off switch is set to on.
2.
Press the on/standby button to turn the heater on.
3.
Press the timer button to set the desired time (between 1 and
24 hours) until heater turn-off. The time is confirmed when the
display stops blinking.
4.
Select the desired temperature and settings prior to heater
turn-off. The tempera- ture is confirmed when the display
stops blinking.
5.
The LED display will show the desired temperature.
6.
To check the remaining time prior to turn-off press the timer
button.
7.
To cancel the turn-off timer turn the heater off and on again
using the on/off switch.
Note: Long-press the timer button to quickly select your desired
time until turn-on or turn-off.
Oscillation
Activates the oscillation function to ensure wide and even heat
Button
distribution. A blue light will show above the oscillation button when
the oscillation function is activated.
Mute Function
To enable the Mute function on your appliance, press down
(only available
simultaneously on the Mode and Temperature Increase button for
on Control
about 2 to 3 seconds. You should hear a beep sound to confirm the
Panel)
activation of the function. To disable the Mute function, repeat the
same process as above.
Child Lock
To enable the Child Lock function on your appliance, press down
Function (only
simultaneously on the Temperature Increase and Temperature
available on
Decrease button for about 2 to 3 seconds. The device will sound one
Control Panel)
beep, after which the display will blink 'LC'. Once the blinking stops,
the Child Lock is official activated.
To disable the Child Lock function, press down simultaneously on
the Temperature Increase and Temperature Decrease button for
about 2 to 3 seconds. The device will sound two beeps, after which
the display will blink 'UN'. Once the blinking stops, the Child Lock is
official de-activated.
Note: You will only hear the beep sounds when your appliance is not
on mute.
12 of 88 | English
NOTES
― ―
•
Overheat Protection - When the temperature of the heater is too high, the thermostat will
automatically switch off the power and the heater will stop working. This may occur during
improper use or certain environmental conditions. After the heater has cooled for 10 to 20
minutes, the heater can be used normally.
•
Tip-Over Protection - When the heater is knocked over or tipped onto its side, the safety
switch will automatically cut off the power. Power will return to normal when the unit has
been placed upright onto an even surface.
CLEANING AND STORAGE
― ―
WARNING: ALWAYS TURN THE HEATER OFF, UNPLUG THE
POWER CORD FROM THE ELECTRICAL OUTLET AND ALLOW
THE APPLIANCE TO COMPLETELY COOL DOWN BEFORE
HANDLING OR CLEANING IT.
WARNING: ALLOW THE HEATER TO COOL DOWN FOR 2
HOURS (120 MINUTES) BEFORE CLEANING.
CAUTION: DO NOT ALLOW WATER OR OTHER LIQUIDS TO
RUN INTO THE INTERIOR OF THE HEATER, AS THIS COULD
CREATE A FIRE AND/OR ELECTRICAL HAZARD.
CAUTION: DO NOT USE ANY ABRASIVE CLEANERS OR
SOLVENTS, AS HEATER DAMAGE WILL OCCUR.
•
Do not attempt to clean the heater in any other way than
that detailed by the manufacturer.
•
Clean the exterior surface of the heater by wiping it with
a soft, damp cloth. Dry the heater with a soft clean cloth.
•
Clean the air inlet and outlet grills regularly with a
vacuum cleaner, using the brush attachment to avoid
any dust build-up.
•
To store your product out of season, we recommend
using the original or similar size box.
•
Do not kink or wrap the power cord and plug around the
appliance, as this may cause the insulation to weaken or
split, particularly where it enters the appliance.
English | 13 of 88
Werbung
