Herunterladen Diese Seite drucken

Sharp GF-4646HT Serviceanleitung Seite 14

Werbung

©)
NOTES
ON
SCHEMATIC
DIAGRAM
GF-4646HT(B) GF-4646HT(B)
1. Resistor:
e
Unless otherwise specified all resistance in ohms,
K = 1000 ohm
2. Capacitor:
3. Voltage reading are measured with Digital Multimeter under
no signal condition in tape position.
(
) : AM mode
: FM mode
——""W-
=: Printed resistor
. Widerstande:
e
Falls nicht anders
angegeben,
sind alle Widerstande
in
Ohm angegeben.
K = 1000 Ohm
. Kondensatoren:
e
Falls
nicht anders
angegeben,
sind alle Kondensatoren
in Mikrofarad angegeben.
P = Picofarad
e
(CH), (RH): TK-Kondensator
. Die Spannungen werden bei Einstellung des Gerates auf die
Tape-Stellung
ohne
Signaleingang
mit DigitalvielfachmeB-
gerat gemessen.
)
: AM-Betriebsart
: UKW-Betriebsart
(
—W-
=: Gedruckter Widerstard
©
e
A
moins de notification
contraire,
toute
résistance est
exprimée en ohms.
K = 1000 ohms
2. Condensateur:
e A moins de notification contraire, toute capaciteé est
exprimeée en microfarads.
P = Picofarads
e
(CH), (RH):
Compensation de température
3. La tension est mesurée a l'aide d'un multimétre numérique
dans les conditions de non signal sur la position ''tape''.
(
)
: Mode AM
: Mode FM
: Résistance imprimée
==
REMARQUES
CONCERNANT
LE
1. Résistance:
5.
6.
7.
5. Die mit
A
7. Anderungen
des
Parts marked with " A\ "' (
) are important for main-
taining the safety of the set.
Be sure to replace these parts
with specified ones for maintaining the safety and perform-
ance of the set.
B and F in Band Selector Switch (SW1), at each mode, are
shown in Table 1 (See page 15). And the Terminals except
the mode in use are connected to the ground.
Schematic diagram and Wiring Side of P.W.Board for this
model are subject to change for improvement without prior
notice.
ANMERKUNGEN
ZUM
SCHEMATISCHEN
SCHALTPLAN
~__)
bezeichneten Teile sind besonders
wichtig
fur die Aufrechterhaltung
der Sicherheit.
Beim
Wechseln
dieser
Teile
sollten
die vorgeschriebenen
Teile
immer
verwendet
werden,
um
sowohl
die Sicherheit
als
auch die Leistung des Gerates aufrechtzuerhalten.
Bund
F im Wellenbereichswahlschalter
(SW1)
werden
in
der Tabelle 1 (Siehe seite 15) angezeigt.
Und die Kiemmen
auRer der verwendenden
Betriebsart werden an die Erdung
angeschlossen.
schematischen
Schaltplans
und
der
Verdrahtungsseite
der
Leiterplatte
fur dieses
Modell
im
Sinne von Verbesserungen jederzeit vorbehalten.
DIAGRAMME
SCHEMATIQUE
—19 —
. Les piéces portant une marque
/\
sont particuliére-
ment
importantes pour la sécurité.
S'assurer de les rem-
placer par des piéces du numéro
de piéce spécifié pour
maintenir la sécurité et la performance de l'appareil.
. Les positions B et F du commutateur de sélection de gam-
me d'ondes
(SW1)
sont indiquées sur le tableau 1 (Voir
page 15).
Les bornes a l'exception de celle du mode utilisé
sont mises a la terre.
. Le diagramme schématique et le cété cablage de la PMI de
ce modeéele sont sujets a modifications
sans
préavis pour
l''amélioration de ce produit.
(E) EQUIVALENT
CIRCUIT (BLOCK DIAGRAM) OF IC, TYPES OF TRANSISTOR
AND LED
(©) ERSATZSCHALTKREIS
(BLOCKSCHALTPLAN)
DES
INTEGRIERTEN
SCHALTKREISES, TRANSISTOREN-UND LEUCHTDIODENTYPEN
(F) CIRCUITS
EQUIVALENTS
(DIAGRAMME
SYNOPTIQUE)
DE Cl, TYPES
DE
TRANSISTOR ET LED
IC2: VHIAN7223//-1
(AN7223)
Cy
iy
G
a3
(BE)
TOP
VIEW
|
elas
tel
ee
Lal
ee
5
P——0—()
1C1: VHITA7335P/—1 (TA7335P)
1C3: VHITA7343P/—1
(TA7343P)
IC201: RH-IX1222AFZZ (LA4192F)
ado
Ecs
2SC945 AP
2SC945 AK
E. EMITTER
C. COLLECTOR
B. BASE
— 20 —
10101: VHIM51544L/—1
(M51544L)
|
|
RVUTTY
GL-9PR25
(Red)
1 ANODE
2 CATHODE

Werbung

loading

Diese Anleitung auch für:

Gf-4646ht b