Werbung
Connect the input/output plug to the receiver SA-11IH/E or
supply +12V by an external DC power supply.
ADJUSTMENT
REMARKS
ITEM
POINT
TONEARM
VR103
Without
TRACKING
compartment,
forward
key to have
down
to the turntable
2.
Turn
the
clockwise
the
inner
back
until
stopped:
semi-variable
ITEM
JIG
ADJUST.
MENT
POINTS
Lead-in
Bladed
screw
Lead-in
position
driver,
LP
adjusting
record
or test
eccentric
record
pin
SSR4005
•see Fig. 7-1 .
(Side 1)
Height of
Bladed
screw
Cue damper
stylus
driver
guide angle
'See Fig. 7-1.
Turntable
LP record
33r.p.m.
speed:
speed
which
is pro-
VRIOI
vided
with
45r.p.m.
speed:
strobo
VR102
viewer
REPLACEMENT
four kinds of phono motors and they can be
There
are
identified by the marks (no mark, red, black. blue) givenat
their
bottoms.
When replacing the existing phono motor with the new one,
it is needed to cut off one of the four resistors (R 162,
R163, RI 64, R165) on the microcomputer
CIRCUIT
ADJUSTMENT
a record being put in the
push
the
cartridge
key first and then the cue
the
tonearm
moving
surface.
semi-variable
resistor
to
move
the
tonearm
in
direction,
and
turn
it
the
tonearm
will
be
at this
position,
fix the
resistor.
MECHANICAL
ADJUSTM
REMARKS
{CHECK)
Stylus tip is at the
central part of the lead-
in groove.
using a test record
Lead-in:
20±2
22±2
(Lead-out:
13±1
18±1)
Adjust so that the
distance
between
the
stylus tip and the record
surface
becomes
4 mm
to 5 mm. At the fine,
make sure that
the tone-
arm
won't
hit
the
rest
support
while it is
returning.
Phono rnotor
is kept in
rotation.
VROI
VRi02
VR103
Figure 7—2 ADJUSTMENT
OF PHONO
player, and the resistor to be cut off must have the same
mark as that given for the new phono motor.
replacement,
computer
been removed when the existing
PWB of the
RP-IIIH(S)
ENT
Low
Lead-in
CD High
Adjustment
of Stylus Adjustment
Hex Wrench
Bladed
Screw-
driver
Figure 7—1
POINTS
MOTORS
it
is further
needed to add to the micro.
PWB the same type of resistor as that which had
phono motor
RP-IIIH(S)
@
SCHALTUNGSEINS
Den Eingangs-/Ausgangsstecker an
(SA-II IH/E)
anschließen Oder dur
nung +12V zuleiten.
BENEN-
EINSTEL.
NUNG
PUNKT
TONARM-
VR103
ABTAS-
TUNG
MECHANISCHE
FÜHRUNGS.
BENEN-
NUNG
LEHRE
Einlauf-
Normaler
position
Schraubenziehe
Langspietplatte
Oder Testschall•
platte
SSR-4005
(Seite 1)
Nadel-
Normaler
höhe
Schrauben.
Mit Strobo-
Platten•
teller-
skopmuster
drehzaht
versehene
Langspiel-
platte
AUSWECHSLUNG
PLATTENSPIELERMOT
Es gibt
vier Arten
können durch Marken (keine Ma
der
Böden
idenzifiziert
vorhandenen
erforderlich,
RI 64, R 165)
Plattenspielers
Widerstand
muß die gleiche Ma
Plattenspielermotor.
erforderl ich,
gleichen Typ von Widerstände
After
the
bei der Verwendung
entfernt
wurde.
was used.
BEMERKUNGEN
Wenn sich
I.
befindet,
Vorlauftaste
lifttaste
d
arm
auf
absenkt.
2.
Den Trim
hen, urn
benzgen,
drehen,
b
stand
kom
Trimmer
EI
EINSTELL.
PUNKT
Einlauf-Ein-
stellexzenter•
Stift
*Siehe
Abb
7-1.
Tonarmlift-
dämpfer
Siehe
Abb
7-1
Drehhal
33
U/min:
VRIOI
Drehzahl
4
Ulmin:
VR102
von Plattens
werden.
Plattenspieiermotors
einen
der
vier W
auf
der
Mikroco
abzuschneiden.
u
Nach der A
zu
der
Mikrocomp
h
des vorhande
Werbung
