Cricut joy JCTR101 Bedienungsanleitung Seite 4

Important safety instructions
PLEASE READ THIS ENTIRE DOCUMENT PRIOR TO
SETTING UP, OPERATING AND SERVICING YOUR
CRICUT® SMART CUTTING MACHINE. PLEASE
FOLLOW THE ENCLOSED INSTRUCTIONS, ONLINE
INSTRUCTIONS AND OTHER OFFICIAL CRICUT
INSTRUCTIONAL MATERIALS. FOR MORE SAFETY
AND COMPLIANCE INFORMATION, GO TO CRICUT.
COM/SAFETY.
In these instructions, the term "Machine" means
Cricut Joy.
WARNING: Risk of Injury, Fire and Electric
Shock.
Operating Machine in a manner not
prescribed in the enclosed instructions,
online instructions and other official Cricut
materials may result in damage to the Machine,
property damage, injury or even death.
Machine is only intended to be operated by
an adult. Not intended for use by children
12 years or under. Always supervise children
around Machine.
Only use Machine for its intended crafting purpose.
Indoor Use Only. Machine is only intended for
indoor use in dry locations. Do not use
in or near water. Do not immerse in water or any
other liquid.
Machine is not intended for use by persons with
reduced physical, sensory or cognitive capabilities,
or lack of experience and knowledge, unless they are
supervised by a person responsible for their safety
and familiar with the safe operation of Machine.
Disconnect the electrical power by unplugging
Machine before servicing or cleaning.
6
Only clean Machine with a soft cloth dampened
with glass cleaner or water. Never use any kind
of flammable liquid to clean Machine. Do not use
solvents such as acetone or nail polish remover to
clean Machine as these will permanently damage
Machine's surfaces.
Always unplug Machine before replacing the cutting
blade. Blades are extremely sharp and should be
handled with caution and extreme care. Prevent
blade contact with hands and body to avoid injury.
Do not allow children to handle blades. Blades and
other small parts are choking hazards and should be
kept and stored away from children.
Do not open, modify or otherwise tamper with
Machine.
Do not operate if Machine or cord is damaged.
Contact Cricut Member Care for service: cricut.
com/contact or 1-877-727-4288.
Only use Cricut-approved power adapters.
Always turn Machine OFF before unplugging from
the electrical outlet. Never pull on the cord to
disconnect Machine from the electrical outlet;
instead, grasp the plug and pull to disconnect
Machine.
The power cord should be positioned so that it
will not drape over the countertop or tabletop
where it can be tripped over, snagged or pulled on
unintentionally (especially by children).
Place Machine on a strong, flat, level and stable
surface. Make sure your work space has enough
space in the front and back of Machine to allow the
cutting mat to move through Machine freely.
Do not place your fingers or other objects in Machine
while connected to electrical power or while Machine
is powered on, or during cutting operations.
Keep hair, jewellery, loose clothing, fingers, other
body parts and any other items that could get
caught in the moving parts away from Machine
while it is operating as the rapid movements of the
cutting carriage, mat and material during operation
may cause injury.
Do not touch the mat or material during cutting,
even if the mat or material stops moving. Do not
Technical specifications
Cricut Joy Models: JCTR101, JCTR101B, JCTR101C
Description: Cricut Joy is a compact cutting and
writing device for do it yourself (DIY) projects.
It takes images created in a software design
environment (Cricut Design Space) and recreates
the images in paper, vinyl, etc. using tools to cut and
write on these materials.
Product specifications
Size (Width x Length x Height)
Weight
Power input (appliance inlet)
External power supply
Operating mode
Electrical classification
Pollution degree
Ingress protection
Wireless specifications
Transmission type
Frequency Band
Maximum Radiated Power
touch the mat or material until Machine ejects the
mat or material from Machine.
Machine should never be left or stored outside,
in unheated or non-air-conditioned spaces, or in
environments where Machine can come in contact
with water.
The overall design is similar to a small desktop
printer or plotter with an electrically driven head
that moves the design tools laterally and feed rollers
that move the crafting materials longitudinally.
The combination of these movements gives 2 axis
motion to perform the desired actions (cutting,
drawing, etc.) on the crafting materials in a two-
dimensional flat plane.
8.3 in x 5.4 in x 4.3 in (21.2 cm x 13.8 cm x 11.0 cm)
3.9 lbs (1.75 kg)
18 Vdc, 2.5 A
Input: 100-240 Vac, 50/60 Hz, 1.5 A; Output: 18 Vdc, 2.5 A
Model: TS-A045-1800251
Continuous
Class III (Supplied by SELV)
PD 2
IPX0 (ordinary)
Bluetooth
2.4000–2.4835 GHz
<= 100 mW (e.i.r.p.)
EN
7