Polti VAPORETTO DIFFUSION Bedienungsanleitung Seite 12

CORRECT USE OF THE PRODUCT
This appliance is intended for home use as a
steam cleaner as described and in accordance
with the instructions provided in this manual.
Please read these instructions carefully and
keep them. If this manual is lost, it can be
consulted and/or downloaded from the website
www.polti.com.
POLTI S.p.A. reserves the right to make any
technical or construction changes it deems
necessary, without prior notice.
Before leaving our factory all our products are
rigorously tested. This is the reason why your
Polti Vaporetto may contain some residual
water in the boiler.
Correct use of the product is only as detailed
in this instruction manual. Any other use may
damage the appliance and invalidate the
warranty.
WHICH WATER TO USE IN THE
BOILER
This appliance has been designed to function
with medium-hardness tap water between
8°f and 20°f. If the tap water is very hard,
do not just use demineralised water but a
mix composed of 50% tap water and 50%
demineralised water which is widely available
to purchase.
Warning: check the hardness of the water at
the technical office at your local council or
the local water supplier.
If you only use tap water, you can reduce the
formation of limescale by using the special
Kalstop (PAEU0094) anti-limescale product,
distributed by Polti, and available for sale at
all major domestic-appliance stores or online
at www.polti.com.
Do not use distilled
demineralised water, rain water or water
containing additives (e.g. starch, perfumes),
scented water or water produced by other
domestic appliances, by water softeners and
filter jugs.
Do not add chemical, natural, detergent, or
limescale removing substances, etc.
1. PREPARATION FOR USE
1.1 Unscrew the safety cap (1).
It is a good idea to check that the boiler is
empty before filling it.
1.2 Fill the boiler with up to 200 ml of water,
using the jug (2).
water, undiluted
| 12 |
WARNING: Never exceed the maximum
boiler fill level of 200 ml; always use the jug
supplied.
1.3 Carefully screw the safety cap back on,
checking that it is completely closed (3).
This step must always be carried out when the
boiler has cooled and with the power cable
disconnected from the mains.
1.4 Only for Polti Vaporetto Diffusion it's
possible to combine steam with FrescoVapor,
a natural deodorant which, in addition to
releasing a pleasant fragrance, eliminates bad
odours.
Please refer to the instructions given in section
7 for how to use Frescovapor.
1.5 Connect the cable plug to an earthed
power supply of the correct voltage (8).
1.6 The "Steam Ready" lamp will turn on.
Wait for the steam ready indicator lamp to
go out (approx. 5 minutes). The appliance is
ready for use.
WARNING: If steam is escaping from the
safety cap, switch the appliance off and
unplug it from the mains. Wait for two hours
for the appliance to cool before unscrewing
the cap and screwing it back on.
2. CONNECTION OF
ACCESSORIES
2.1 FLEX (only for model Polti Vaporetto
Diffusion)
• To join the flex to the appliance, bring the
arrow on the flex into line with the single
notch on the appliance and then rotate the
flex body in the direction of the arrow, until
it clicks into place (12).
• To release the flex, pull the little lever above
it and rotate in the opposite direction from
before (13).
• In turn, the lance can be connected to the
flex and therefore all other accessories
supplied.
2.2 LANCE
To attach the lance, bring the arrow on the
lance into line with the single notch on the
appliance and then rotate the lance in the
direction of the arrow until it clicks into place
(14).
The following accessories can be attached to
the lance:
• window-washing accessory, curved nozzle,
round brushes, spatula and accessory for
grouting. Simply insert them into the lance
tip and rotate until they lock into place (15).