Trevi OM 3530 RC Bedienungsanleitung Seite 5

OM 3530 RC
EXTERNAL SENSOR SETTING
This weather station is designed to communicate with three
external sensors. One of these is supplied with the device, the
remaining two are optional.
1. First of all, power up the central unit, as described in the
POWER SUPPLY - CENTRAL UNIT paragraph;
2. Within 3 minutes from the activation of the central unit, insert
the batteries in the external sensor, and select channel CH 1
on the external sensor
3. Press the TX key, a signal will be automatically transmitted
to the central unit and, when hooking up, the icon (8) will be
displayed;
4. The weather station will display the temperature value of
channel "1" transmitted by the external sensor (9) on the dial.
If you have two other sensors, proceed according to points
"2" and "3", the station will stores the values respectively in
channels 2 and 3.
Note:
- Remove the batteries if you do not use the device for a long
period of time.
- Replace the batteries when the display numbers become
less legible or the icon
- After inserting the batteries in the external sensor, the central
unit begins to receive the signal, the antenna symbol (8)
will flashes for a few minutes and then goes off once the
connection is successful. If the indication of the external
temperature does not occur within 15 minutes:
- Remove the batteries from both units to perform a full reset.
- Press the TEST key of the transmitter located under the
battery compartment.
- The central unit will receive the external temperature auto-
matically from channel 1 to channel 3.
- Place the transmitter outdoors in a suitable place. In order to
ensure good transmission at 433MHz, the distance between
the sensor and the unit must not exceed 30 meters.
TIME DISPLAY VIA RADIO CONTROL
This device is equipped with a receiver capable of receiving the
time signal of the Physikalisch Technische Bundesanstalt Braun-
schweig (Central Germany) receivable in a radius of 1500Km.
When the batteries are inserted, signal reception will automati-
cally activate, the radio control symbol (1) will flash and within
24 hours the radio control time signal will be displayed and the
radio control indication (1) will remain fixed.
If you need to restart signal reception, hold down the DOWN key
(16) for a few seconds.
- If after 10 minutes the DCF signal is not received, use the
MODE/SET(18) key to set the time manually. The clock will
automatically try to lock onto the DCF signal every hour. When
this is detected, the received time will overlap the manually
set time. The date will also be updated with the date received.
;
appears on the display.
DIGITAL CLOCK
TIME ZONE
The time is transmitted from central Germany, so if we are in a
country with a different time from that of Germany need to set
the time zone.
1. Once the time signal is detected, hold down the MODE/SET(18)
key for a few seconds to enter the manual clock adjustment.
The "24h" or "12h" time format setting will appear;
2. Press the MODE/SET(18) key again, the display will show
"00" with the ZONE icon (6) flashing;
3. Set the time zone of your region using the UP(17) or DOWN(16)
keys.
Note:
Place the clock away from devices that generate magnetic fields
such as cell phones, televisions, etc.
It may not be possible to receive the radio control signal in all areas
of Europe. In this case it is necessary to set the time manually.
MANUAL ADJUSTMENT OF THE CLOCK AND DATE
1. Press and hold the MODE/SET(18) key for 3 seconds;
2. Press the UP(17) or DOWN(16) keys to set the time view in
12 or 24 hour format;
3. Press the MODE/SET(18) key to switch to the ZONE function;
4. Press the UP(17) or DOWN(16) keys to adjust the time zone;
5. Press the MODE/SET(18) key to move to setting the time,
use the UP(17) or DOWN(16) keys to set it;
6. Press the MODE/SET(18) key to move on to setting the
minutes, use the UP(17) or DOWN(16) keys to set them;
7. Press the MODE/SET(18) key to move to setting the year, use
the UP(17) or DOWN(16) keys to set it;
8. Press the MODE/SET(18) key to move to setting the month,
use the UP(17) or DOWN(16) keys to set it;
9. Press the MODE/SET(18) key to move on to setting the date,
use the UP(17) or DOWN(16) keys to set it;
10. Press the MODE/SET(18) key to switch to setting the language
of the days of the week, use the UP(17) or DOWN(16) keys
to set the preferred language.
Note: There are 8 languages available for the days of the week:
English> German> French> Italian> Dutch> Spanish>
Danish> Russian.
11. Press the MODE/SET(18) key to confirm the settings or wait
20 seconds without pressing any button to return to the
normal display.
CELSIUS - FAHRENHEIT GRADES SELECTION
Press the DOWN(16) key to display the temperature in degrees
Celsius (°C) or Fahrenheit (°F).
ENGLISH