Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
HG210ED(EN).fm Page 6 Tuesday, March 2, 2004 4:08 PM
Note:
You may also access the RF OUT CH menu by pressing
and holding
MENU
on the remote control for 3 seconds
during power off until the RF OUT CH menu appears.
MENU
TIMER
SET UP
INITIAL
Setting the Clock
This VCR incorporates a 24-hour clock. The clock must be set
for the Timer Recording function to operate correctly.
• Use the remote control for this procedure.
1) Press
MENU
.
2) Press
PLAY
/
or
STOP
/
o
L
F.FWD
/
.
B
3) Press
PLAY
/
or
STOP
/
o
L
F.FWD
/
.
B
4) Press
PLAY
/
or
STOP
/
o
L
then press
F.FWD
/
.
B
5) Press
PLAY
/
or
STOP
/
o
L
appears, then press
F.FWD
6) Press
PLAY
/
or
STOP
/
o
L
then press
F.FWD
/
.
B
7) Press
PLAY
/
or
STOP
/
o
L
then press
F.FWD
/
.
B
8) Press
PLAY
/
or
STOP
/
o
L
appears.
9) Press
MENU
to start the clock.
Note:
REW
• Press
/
to go one step back from the current step
s
5)
8)
during steps
to
.
• Although seconds are not displayed, they begin counting
from 00 when you exit by pressing
to synchronize the clock with the correct time.
• If the VCR is unplugged or if there is a power failure for
more than 30 seconds, you may have to reset the clock.
MENU
TIMER
SET UP
INITIAL
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
RF OUT CH 36
to select "INITIAL", then press
to select "CLOCK", then press
until the relevant year appears,
until the relevant month
/
.
B
until the relevant day appears,
until the relevant hour appears,
until the relevant minute
MENU
. Use this feature
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
CLOCK
YEAR
2 0 0 4
MONTH
0 1
DAY
0 7 WE
_ _
HOUR
_ _
MINUTE
Channel Presetting
Tuning of broadcast channels not already preset in the VCR
can be performed in two ways.
Automatic Channel Preset
• By "AUTOMATICALLY" tuning channels and placing
them in sequential order in the VCR's memory i.e. the first
channel found will be memorized into the VCR's channel
position 1, the second channel found will be memorized
into the VCR's channel position 2 and so on.
• Execution of the "Automatic" channel presetting cancels all
the preset channels. DO NOT use this feature if you intend
to use some of the pre-tuned channels. Use the "Manual"
channel presetting function to tune in the additional
channels you require.
Manual Channel Preset
• Each channel is tuned manually and individually. Follow
the steps laid out in the "Manual Channel Preset" section.
Before you preset Channel...
• It is necessary to set the video channel if your VCR is
connected to the TV via the coaxial cable, and TV channel
36 is set for broadcasting, or interference lines appear on
the picture. Please refer to "Video Channel Setting".
Automatic Channel Preset
You can programme the tuner to scan only the channels that
you can receive in your area.
• Use the remote control for this procedure.
1) Turn on the TV and select the TV channel to the video
channel on the TV.
2) Press
MENU
.
3) Press
PLAY
/
or
STOP
/
o
L
F.FWD
/
.
B
4) Press
PLAY
/
or
STOP
/
o
L
press
F.FWD
/
.
B
5) Press
PLAY
/
or
STOP
/
o
L
F.FWD
/
.
B
• The tuner scans and memorizes all the active channels in
your area. After scanning, the tuner stops on the lowest
memorized channel.
MENU
TIMER
SET UP
INITIAL
scanning
6
to select "INITIAL", then press
to select "CH TUNING", then
to select "AUTO", then press
INITIAL
CH TUNING
CLOCK
RF OUT
LANGUAGE
CH TUNING
AUTO
MANUAL
MOVE
EN
Werbung
Kapitel
Inhaltsverzeichnis
Fehlerbehebung
