Seite 1
Falls er forderlich, kontaktieren Sie uns bitte, um die neueste Version der Gebrauchsanweisung zu erhalten. NASync DXP2800 Network Attached Storage 由于产品 升 级,图 示、 参 数 等 信息 和实 物 略 有差 异, 请以 实 物 为准 。 User Manual | Benutzerhandbuch | 用户手册...
Seite 2
Contents Inhalt About the DXP2800 Über den DXP2800 Instructions Before Use Anweisungen vor dem Gebrauch Package Contents Inhalt der Verpackung Product Overview Produktübersicht 24-25 Installing 3.5-inch Hard Drives Installation von 3,5"-Festplatten 26-27 Installing 2.5-inch Hard Drives Installation von 2,5"-Festplatten 28-29 Installing M.2 SSDs 9-11 Installation von M.2-Festplatte...
Seite 4
About the DXP2800 Package Contents UGREEN DXP2800 is a network-attached storage device designed for home and personal users. The DXP2800 works as an intelligent data management center where users can store and access data via smartphones, laptops, tablets, and TVs anywhere there is network access.
Seite 5
Product Overview Magnetic Dust Mesh Filter HDMI Port USB 3.2 Gen 1 Port 2×USB 2.0 Port Power Port 1×2.5GbE Ethernet Port Reset Hole 1×Memory Slot (with one memory Safety Lock module pre-installed) 2×M.2 Slot (optional) Panel Power Button (Loosen the screws to remove it ) Power Indicator...
Seite 6
Unlocking Hard Drive Tray 2. Place hard drive on the tray following the Use the key to unlock the hard drive tray, press the buckle to pop the handle out, then pull the tray out. angle shown in the figure. Ensure the four fastening pins on the tray (two on each side) are aligned with the screw holes on the hard drive.
Seite 7
Installing 2.5-inch Hard Drives 1. Remove the fastening pin as shown. 3. Turn the tray upside down and tighten the screws to secure the drive in place. Then insert loaded Note: Removed fastening pins can be attached in fixed holes near the tray covering incase they are drive tray into empty drive bay and push the handle to fasten in place.
Seite 8
Installing M.2 SSDs (Optional) 2. Insert M.2 SSD into the slot in the direction shown by the image below. What does installing an M.2 SSD do? M.2 SSDs can be used as a normal storage drive or as a read/write cache to improve reading and writing performance of random data.
Seite 9
Powering On 4. Reinstall the tray and power on the NAS. After successful boot up, go to the "UGREEN NAS" app to Use Ethernet cable to connect NAS to a LAN port on a router. Connect the power adapter to the device, set the SSD cache.
Seite 10
Note: If the device does not undergo the initialization process, its status will be displayed as Buzzer "Not Initialized". Step 3: Set up Storage Mode Status Beeper Enter the "UGREEN NAS" > "Storage Manager", then you can set up storage mode and configure Power on Short beep once storage space. System reset Short beep once...
Seite 11
① Please ensure that the NAS device and your phone or computer are on the same LAN. ② Open "UGREEN NAS". The system will automatically search for devices. You can also add a · In JBOD storage mode, failure of a single hard drive amounts to storage failure for all drives.
Seite 12
"Add" to create a new user account, and provides the account and password to the invited user; data through the PC, browser, and mobile app without adjusting complicated network settings. the invited user logs in to the "UGREEN NAS", searches for the device via the LAN, then enters M.2 Capability Extension the account password to activate the account and bind the device.
Seite 13
· OF CHILDREN Do not dismantle or fix the NAS device by yourself. Improper disassembly and assembly may cause electric shock or other safety hazards. If repair or replacement parts and/or accessories are required, please contact UGREEN customer service.
Seite 14
SODIMM DDR5 Memory Capacity 8GB/16GB (max memory size) Flash Memory 32GB eMMC Internal: ext4/Btrfs External: Btrfs/ext2/ext3/ext4/VFAT/exFAT/FAT16/FAT32/NTFS/XFS File System Internal non-"UGREEN NAS" storage pool: Btrfs/ext2/ext3/ext4/VFAT/exFAT/FAT16/FAT32/NTFS/XFS Storage Mode JBOD/Basic/RAID 0/RAID 1 2×2.5-inch/3.5-inch SATA hard drive Supported Drive 2×M.2 NVMe 2280 SSD Video Port 1×HDMI, Up to 4K...
Seite 15
Über den DXP2800 UGREEN DXP2800 ist ein Netzwerkspeichergerät, das für Heim- und Privatanwender entwickelt wurde. Der DXP2800 dient als intelligentes Datenverwaltungszentrum, in dem Benutzer Daten speichern und über Smartphones, Laptops, Tablets und Fernsehgeräte überall dort abrufen können, wo ein Netzwerkzugang besteht.
Seite 16
Inhalt der Verpackung Produktübersicht 2×Festplattenfach- 1×Netzwerkspeicher 1×Bedienungsanleitung 1×Garantiekarte Schlüssel Sicherheitsschloss Einschalttaste Betriebsanzeige Netzwerk-Anzeige USB 3.2 Gen 2-Anschluss Festplatten-Anzeige Typ-C USB 3.2 Gen 2 Anschluss 1×Ethernet-Kabel 1×Netzteil Schrauben und (CAT7) (DC 12V/5A) Schraubendreher (für den Einbau von 2,5"-Festplatten)
Seite 17
Entriegeln des Festplattenfachs Magnetischer Staubfilter Entriegeln Sie das Festplattenfach mit dem Schlüssel, drücken Sie auf die Schnalle, um den Griff herauszuziehen, und ziehen Sie dann das Fach heraus. HDMI-Anschluss USB 3.2 Gen 1-Anschluss 2×USB 2.0-Anschluss Stromanschluss 1×2,5-Gigabit-Ethernet-Anschluss Reset-Loch 1×Speichersteckplatz (mit einem vorinstallierten 2×...
Seite 18
Installation von 2,5"-Festplatten 2. Legen Sie die Festplatte in dem in der 1. Entfernen Sie den Montagestift wie abgebildet. Abbildung gezeigten Winkel auf dem Fach. Hinweis: Die entfernten Montagestifte können in die festen Löcher in der Nähe der Fachabdeckung Stellen Sie sicher, dass die vier Montagestifte eingesetzt werden, wenn sie für 3,5"-Festplattenlaufwerke benötigt werden."...
Seite 19
Installation von M.2-Festplatten (optional) 3. Drehen Sie das Fach um und ziehen Sie die Schrauben fest, um das Laufwerk zu befestigen. Legen Sie dann den geladenen Laufwerksträger in den leeren Laufwerksträger ein und drücken Sie den Griff, um sie zu sichern. Wozu dient die Installation einer M.2-Festplatte? M.2-Festplatten können als normales Speicherlaufwerk oder als Lese-/Schreibcache verwendet werden, um die Lese- und Schreibleistung von Zufallsdaten zu verbessern.
Seite 20
2. Setzen Sie die M.2-Festplatte wie in der Abbildung unten gezeigt in den Steckplatz ein. 4. Setzen Sie den Steckplatz wieder ein und schalten Sie das Netzwerkspeichergerät ein. Nach dem erfolgreichen Hochfahren rufen Sie die App "UGREEN NAS" auf, um den Festplatte-Cache einzustellen. Hinweis: Um den richtigen Sitz zu gewährleisten, sollte die Kerbe mit der entsprechenden Kante im Schlitz ausgerichtet sein.
Seite 21
Routers an. Schließen Sie den Netzadapter an das Gerät an und drücken Sie kurz die Ein-/Austaste, um es einzuschalten. Statisch Einschalten Tipps: Nach dem Einschalten können Sie "UGREEN NAS" herunterladen und dann unter "Systemsteuerung" Weiß Blinkend (einmal pro 0,5 s) Ausschalten >...
Seite 22
· Benennen Sie das Gerät: Benennen Sie Ihr Gerät, um sicherzustellen, dass es leicht zu UGREEN Cloud Konto registrieren und Ihr Gerät vernüpfen möchten. Falls nicht, können Sie diesen Schritt überspringen und sich nur mit dem lokalen Konto beim Gerät anmelden.
Seite 23
Festplatten. Es ist keine Datenredundanz vorgesehen. Wenn eine Festplatte ausfällt, können alle Daten nicht wiederhergestellt werden. sich im „UGREEN NAS“ an, sucht nach das Gerät über das LAN, und gibt dann das Passwort Erfordert nur 1 Festplattenlaufwerk. Die verfügbare Kapazität entspricht der Kapazität des Festplatten- des Kontos ein, um das Konto zu aktivieren und um sich mit dem Gerät zu verbinden.
Seite 24
Cache verwenden, um die Lese-/Schreibleistung zu verbessern. Lieblingstitel immer im Handumdrehen haben. Erstellen Sie personalisierte Wiedergabelisten für Einzelheiten und die Installation finden Sie unter "UGREEN NAS" > "Hilfecenter" > "Wissenscenter" jede Stimmung und jeden Anlass und tauchen Sie ein in eine überragende Klangqualität, bei der Ihnen jede Note noch lange nach dem Verklingen in Erinnerung bleibt.
Seite 25
Falls die Bat terie ausläuf t, vermeiden Sie den Kontak t mit Haut oder Augen. Bei Kontak t mit Dateisystem Interner Nicht-„ UGREEN NAS “-Speicherpool: Haut oder Augen spülen Sie diese mit Wasser aus und suchen Sie sofor t einen Arzt auf.
Seite 31
设备开机 4. 装回托架, 将设备开机, 待设备稳定运行后前往「绿联云」客户端设置 SSD 缓存。 用网线将设备连接至路由器的 L AN 口, 接通电源适配器, 短按电源键开机。 提示: 开机后, 安装并登录「绿联云」App > 「控制面板」 > 「硬件与电源」 , 设置通电自动开机。 L A N 本 机 标 配电源 ( D C12 V/5 A ) 在拆卸 M.2 硬盘之前, 请先前往「绿联云」客户端移除 SSD 缓存, 警告...
Seite 32
指示灯 电脑 Web 端—绑定与设置 第一步 添加设备 L E D 指 示 灯 颜 色 状 态 说 明 ① 请确保设备和电脑在同一局域网内,访问网址:find.ugnas.com。 ② 系统将自动搜索并显示您当前局域网内的设备。 常亮 开机 ③ 选择您要添加的设备,然后点击“连接”。 白色 闪烁 (每 0.5 秒一次) 关机中 电源指示灯 呼吸慢闪 系统休眠 第二步 初始化设备 ① 添加设备后,您将进入初始化设备界面。 橙色 慢闪...
Seite 33
手机/平板电脑等设备—绑定与设置 存储模式说明 1. 客户端下载 硬 盘 组合 所需 硬 盘 数 功能 说明 方式一:手机扫描下方二维码或设备上的二维码,安装「 绿联云」 App。 模 式 方式二:请前往请前往 绿联官网 (https://www.ugnas.com/download),下载和安装客户端。 至少合并两个硬盘来创建存储池, 存储池的可用容量等于该存储池中所有硬盘的总容量。 J B O D 不提供数据冗余。 任意一个硬盘损坏, 存储池数据将永久丢失。 只需一个硬盘即可创建存储池, 存储池的可用容量等于该硬盘的容量。 B a s i c 不提供数据冗余。 硬盘损坏, 存储池数据将永久丢失不可恢复。 至少需要两个硬盘来创建存储池,...