Cooling And Mounting; Bec / Running Without Bec; Torodial Core; Active Freewheeling Circuit - Kontronik JIVE Pro 80+ HV Bedienungsanleitung

long signal tone:
short signal tone:
As for example:
1 short + 1 long tone:
2 long + 2 short tones:
• Very sensitive control ch a r a ct e ristic : smooth
s ta r t- u p .
• Sensing and computing of the actual motor
d a t a: self adjusting clock f r eq u e n c y ( 32 kHz or
hi g h e r ), dynamic t i m in g
• Start protection at power up, block e d motor
protection, over temperature pro tection, over
current limit a tion .
• Digital microprocessor control : therefore no
thermal d ri ft .
• U pd a t a bl e: online firmware update po ssi b l e .
• Please note, that the JIVE Pro ESC is not
PROGCARD comp a tibl e.
• 24 months w a rr a nty : for items with EU proof of
p ur c h a s e .
• CE t e st e d
• Fast repair s e rvic e: in-house service ce n t re.
• Free of charge Hotline (w h e n calling f r om
Ge r ma ny ) : during our daily business h o urs.
For information to
www.kontronik.com (Se rvi ce- C e n te r )
• Developed and produced in Rott e nburg ,
G e rm a ny .

4.2 Cooling and mounting

Sufficient cooling increases the efficiency a n d
lifespan of the ESC. When mounting the ESC to
the model, make sure to mount it with the
cooling plate facing upward. If using a h ea t sink, it
should be placed fins up, and uncovered. When
installing the heatsink, for the best transfer
between the cooling compo nents, KONTRONIK
recommends attaching the h eat sin k with a thermal
paste. For more cooling, you may attach a fan by
screwing it onto the heat sink and plugging it
directly into the JIVE Pro.
4.3 BEC
The JIVE Pro ESC has a switched BEC.
Compared to general BEC-systems the capa city
of the BEC is designed to be independent of the
input voltage. This allows the usage of the BEC at
higher voltages. In addition, the JIVE Pro features
a high interference r e j ect i o n.
BEC capacity of JIVE Pro
8 A continuous
20 A max peak c urr e n t
4 Cells recognized
1 Cell recognized
5 Cells
10 Cells
business hours see:
BEC Volt a g e (default 5.6 V)
The BEC-voltage can be adjusted from 5 V to 8 V
( in 0.1 V s tep s ) by using the programming unit.
For safety reasons,
connecting either a 2-cell LiFePo b atte r y
!
(ad jus ted BEC voltage: 6,6 V – 7 V) or a 2-cell
LiPo b atte r y (ad jus ted BEC voltage: 8 V) or a
4-cell NiCd battery (ad jus ted BEC voltage: 5,6
V) in parallel to the receiver.
!
ATTENTION: please ensure the servos and
r ecei ver are compatible with the requested
v oltage
O peration without BEC:
When operating without BEC, the red receiver
cable is to be disconnected or removed .

4.4 Torodial core

The factory mounted torodial core on the receiver
cable allows suppression of in te r fe rence. It must
not be removed from the cable for security
reasons, but it can be moved, i f necessary,
anywhere within the cab l e.
Never remove the torodial core from the cable!
Itcan be moved within the cable to any position, but
take care for tight fit of the cables afterwards

4.5 Active freewheeling circuit

To optimize the efficiency of partial load operation
and to reduce heating of the ESC, the JIVE Pro
features an active freewheeling circuit. The active
freewheeling circuit should not be used at very
low throttle settings as this may result in
discontinuity of motor RPM.

4.6 Part load capability

Due to its active freewheeling circuit, the ESC
may be operated in partial load conditions if you
do not exceed the JIVE Pro's continuous current
limits during operation.

4.7 Sensorless Commutation

JIVE Pro ESCs work without sensors insi de the
motor via a 3D recognition sys tem . Commutation
of the motor will a u tomat i ca lly be optimized for the
app li cat i o n.

4.8 Variable clock frequency

The JIVE Pro ESC uses a clock frequency of
32 kHz, or higher. Depending on the operational
we recommend
.
15