Bauknecht B8 D94WB EE Kurzanleitung

Quick guide
THANK YOU FOR BUYING A BAUKNECHT PRODUCT.
In order to receive a more complete assistance,
pleaseregister your product on
www.bauknecht.eu/register
PLEASE SCAN THE QR CODE ON YOUR APPLIANCE IN ORDER TO REACH MORE INFORMATION.
CONTROL PANEL
Programme selection knob
1
On/Off button
2
Start/Pause button
3
Options buttons
Gentle Power
4
Crease Care
5
Cycle End Signal
6
Cycle Options (hold for Settings)
7
Dryness Level
8
Timed Drying
9
Start Delay
10
Navigation buttons and Key Lock
UP
11
DOWN
12
CONFIRM OK (hold for Key Lock)
13
INDICATORS
Cycle phase: Drying -
Empty water tank -
Refer to Troubleshooting section:
FIRST TIME USE
When starting the appliance the first time, the control panel will
automatically show the set language menu. The UP and DOWN
buttons are used to show the languages available in the machine.
Press the OK button to confirm. The machine cannot be used
without having selected the language.
Make sure that the water tank is correctly inserted.
The dryer must be installed in a room with a temperature ranging
between 5°C and 35°C to ensure proper operation.
Before using the dryer make sure it has been in an upright
position for at least 6 hours. Should you wish to change the
opening side of the door, please contact our After-sales Service.
(See phone number in the warranty booklet).
DAILY USE
Doing this will keep your machine working at its BEST:
- remember to empty your water tank after each drying cycle.
- remember to clean your filters after each drying cycle.
Refer to the Care & Maintenance section.
1. Plug the dryer into the power supply socket.
2. Open the door and load garments; always refer to instructions on
clothing labels and the max loads indicated in the programme
section. Empty pockets. Make sure garments do not get caught
between the door and/or the door filter. Do not load items that are
dripping wet. Do not tumble dry large, very bulky items. For optimal
drying result, garments should be loaded one by one.
3. Close the door.
4. Press the "On/Off" button.
5. Select the most suitable programme for the type of fabric in that
load.
6. Select the options, if necessary.
7. Press the "Start/Pause" button to begin drying.
8. At the end of the drying cycle, a buzzer will beep. An indicator on
the control panel signals the end of the cycle. Turn the machine
off by pressing the "On/Off" button, open the door and pull the
clothing immediately out to prevent the formation of creases on
laundry.
If the machine is not switched off manually, after about a quarter of an
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
hour from the end of the cycle , the appliance turns off automatically
• Using QR code in your appliance
to save energy. • Visiting our website docs.bauknecht.eu and parts-selfservice.whirlpool.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-sales
Note that some programme/option accords with "Crease Care"
Service, please state the codes provided on your product's identifi cation plate.
system. This means that for some hours, after the end of the drying
cycle, the drum rotates at regular intervals to prevent the formation of
creases.
Note that some models perform a final cool tumble phase, for this
reason the fabrics may not feel hot.
In case of power failure, it is necessary to press the "Start/Pause"
button to restart the cycle.
1
Cool Down
Clean secondary filter -
Failure call After-sales Service
Before using the appliance carefully Before using the appliance carefully
read the Safety Instruction. read the Safety Instruction.
5
6
7
EXTRA
8
Clogged door filters -
Eco Monitor
This indicator shows the energy consumption level according to the
programme and the options set. The consumption is proportional to
the lines on the display, by the ecomonitor icon.
Opening the door during the cycle
The tumble dryer door can be opened at any time during the cycle to
check progress and remove any garments already dry.
However, since opening the door can extend the drying time, the
recommendation is to keep the door closed throughout the cycle
process to save time and energy.
After closing the door, press the "Start/Pause" button within 15
minutes to resume the machine operation.
NOTE: in any case, the drying cycle must be completed to ensure the
condenser auto-cleaning phase is finalized.
NAVIGATION
The "UP" and "DOWN" buttons are used to navigate the available
menus.
• Press the OK button to confirm the selection.
• Press the Option button at the
display, to return to the previous screen.
If no selection is confirmed, after about 10 seconds, the display
return to the main screen.
SETTINGS
To access the Settings menu, press and hold the relevant button for a
few seconds.
• Set language shows the available languages on the display.
• Sounds allows to enable or disable the sounds (some sounds, as
warnings, will remain active anyway).
• Brightness allows to modify the display brightness.
• Factory Default allows to reset the default settings. After having
selected the setting, press and hold the OK button for a few seconds.
CARE LABEL
Always check the care labels, especially when placing garments in
the tumble dryer for the fi rst time. Below are the most commonly
used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
1:35
SYNTHETICS
-:--
-:--
9 10
Autoclean - Eco Monitor
symbol, where present on the
EN
2
11
12
4
13
3