8BITDO Lite 2 Kurzanleitung

8BitD0
Lite 2 Bluetooth gamepad —instruction manual
mode switch
- select
L3
d-pad
star
status LED
R2
pair power LED
Switch
• please ensure your Switch system and Lite SEare updated to the latest version
• NFCscanning, IR camera, HD rumble, notification LEDare not supported, nor can the system be waken
up wirelessly
• status LEDcan indicate upto 8 players
Bluetooth connection
1 — turn the mode switch to S
2 —press home to turn on the controller, LEDstarts to rotate from left to right
3 — press pair button for 3 seconds to enter its pairing mode. LEDstops blinking for a short moment then
starts to rotate again. (This is required for the very first time only)
4 —go to your Switch Home page to click on "Controllers", then click on "Change grip/order" and wait for
the connection
5 — LED becomes solid and the controller vibrates when connection is successful
wired connection
• goto System Setting > Controller and Sensors >turn on Pro Controller Wired Communication
1 — turn the mode switch to S
2 —connect the controller to your Switch dock via USBcable
3 —wait till the controller is successfully recognized by your Switch to play
Android
• please ensure your Android and Lite 2 are updated to the latest version
Bluetooth connection
1 — turn the mode switch to D
2 —press home to turn on the controller, LED1starts to blink
3 — press pair button for 3 seconds to enter pairing mode. LEDstops blinking for a short moment then
starts to rotate again. (This is required for the very first time only)
4 —go to yourAndroiddevice'sBluetoothsetting, and pair with [88itDoLite 2)
5 — LED becomes solid and the controller vibrates when connection is successful
Wired Connection
• OTG support is required on your Android device. Please contact your device manufacturer for more details
1 — turn the mode switch to D
2 —connect the controller to your Android device via USBcable
3 —wait till the controller is successfully recognized by your Android device to play
Turbo function
• hold the button you would like to set turbo to, then press the star button to activate/deactivate
• D-Pad,Left stick, Right stick, Home, Select, Start buttons are not included
• turbo function is not available on Switch mode
battery
status — LED indicator —
low battery
red LED blinks
charging red LEDstays solid
fully charged red LEDturns off
• About 20 hours of play time with a 480mAh built-in battery pack, rechargeable with 1 hour charging time
• controller will turn offin 1 minute with no connection and 15 minutes with Bluetooth connection
• controller stays on with vilred connection
support
• please visit support.8bitdo.com for further information additional support
8BitD0
Lite 2 -
English
+ start - select
L3
R3
home
L2 R2
Switch
* Switch
• NFC
1-8
2. [home
4. switch /
• - - [Pro
2. USB Switch USB
Android iQå
Android
2. [home H-E#, 1
4. Android u,
Android OTG ljJfiE,
2. Android USB
Turbo E&IjfiE
the function
[G / [home], [selectls [start]
* Switch
• 1
but no use
1 15
• iå%support.8bitdo.cn
8BitD0
Lite 2 Bluetoothaysa—3—
+ start - select
L3
R3
home
L2 R2
Switch
Bluetooth
2. [home]
4. sa—3—]
1. rSJ
2. Switch
Android
Bluetooth
2. (homel
nn-3-&
[8BitD0 Lite 2] 4. Android
* Android
2. Android
[+9;fi5 [hÄi4yO Y], [EÄi-fy5
20
8BitD0
- Lite ETT_
+ start - select
L3
R3
home
L2 R2
Switch
A1-g-öPl
• NFC
2. [home
3. [OHE
4. Switch
5.2338
•
1.
2.
USB
*
Android
Android
1 2. [home
3.
4. Android
[M [8BitDo Lite 2]
1.
USB
1.
[home Y], [select [start
* SwitchOll
•
•
support.8bitdo.com •
+ start
R3
home
L2
eEll .ÆAIÉ
Switch 0101 Elo-I WICE
HD
Zl Ell-sol
3 ÆEAI 1 01
71b •YEIl]e
SOI
71SOl
MXI [s]
Switch USB
Ndl Elo-1
IS 1
315] 3 01
['NX'] [æ [8BitDo Lite 2]
Android OTG 71b* XIBöh-É-Xl #89.
+NAIQ.
Nil [D]
Android USB
71B 71>315 -köS 31] -SAIOII POI 71+1 Algol
71-EOI
91, 4*1, ég, home, select, start 9 IS XlaöhXl ?-e-L-lCt.
21501?
EEt _ a E 4 Oil
-Præ
*101
Ila support.8bitdo.com oilA-i '-.21_lCh.
[OH
e