Werbung
Verfügbare Sprachen
Verfügbare Sprachen
4 Operation
The LED panels can be conveniently oper-
ated by means of one of the following re-
mote controls:
4.1 LEDP-99RC
ON
OFF
ALL
A
B
1
2
3
4
5
6
7
8
9
ID
0
S
When a button is pressed, the red LED in-
dicator above the blue button will light up.
4.1.1 Inserting / Replacing batteries
Remove the battery compartment cover
on the rear side and insert two batteries
(2 × 1.5 V, size AAA) as indicated in the
compartment.
Never put batteries in the house-
hold waste. To protect the environ-
ment, always take them to a spe-
cial waste disposal, e. g. collection
container at your retailer.
4.1.2 Address assignment
For operation by means of the remote con-
trol, each LED panel requires an address be-
tween 1 and 99. If multiple panels are to be
controlled together, the same address can be
assigned to as many panels as desired. Thus,
it is possible to define 99 panel groups that
are differently controlled.
1) Switch off the panels (i. e. disconnect
them from the mains) to which the
same address is to be assigned for more
than 3 seconds, and then switch them
on again. Then perform steps 2 and 3
within 10 seconds!
2) Use the buttons 1 – 9, 0 to select the de-
sired address (1 – 99) and then press the
button ID.
3) Repeat step 2; as a confirmation of the
input, the panel will briefy get dark.
4) Then, within 10 seconds, switch off the
panel again (i. e. disconnect it from the
mains). The address assignment will be
saved.
5) After another 5 seconds, the panel can
again be connected to the mains. The
panel can then be operated by means of
the remote control.
6) To assign a different address to other pan-
els, repeat steps 1 to 5.
8
4.1.3 Operation with multiple LEDP-99RC
Multiple remote controls may be used to op-
erate the panels from different locations in
the room. The programming of the remote
control that was used for address assign-
ment of the panels must be transferred to
the additional remote controls:
On the remote control that has already
been programmed, keep the power button
I pressed for 6 seconds, while, at the same
4.1.4 Functions
Buttons
Function
1 – 9, 0
Select address of the panel to be set
ALL
select all panels
I
Switch on and off
Select colour tone level (colour temperature)
Select brightness level
Night mode (low brightness level):
Switch off the panel with the button and
switch it on again with the button .
Continuous brightness adjustment
Continuous colour tone adjustment
Automatic colour tone change:
1) Enter the panel address and press the button ID.
2) Press the buttons shown to the left one after the other. The colour tone change
will start.
3) To terminate the colour tone change, use the button
of the buttons for a colour tone level or brightness level.
To save two light settings (scenes):
1) Adjust the colour tone and brightness for the first scene.
2) Enter the panel address; press the button ID and then the button A. The scene
A
B
will be saved; the panel will briefly get dark as a confirmation.
3) For the second scene, repeat steps 1 and 2; however, press button B instead of
button A.
4) Now the scenes can be called up at any time with the buttons A and B.
Automatic switch-on/switch-off:
1) Enter the panel address and press the button ID.
2) Use the buttons 1 – 9, 0 to select the time until switch-on/switch-off:
1 = 10 minutes
99 = 990 minutes (16.5 hours)
3) For the switch-on function, press the button
(the panel will light up briefly as a confirmation)
ON
OFF
or
for the switch-off function, press the button
4) To deactivate the switch-off / switch-on function prior to expiration of the time set:
Enter the panel address and press the button ID. Then press the button
the button
To be able to operate the panel after automatic switch-on/switch-off, enter the
panel address.
No function
time, keeping the button S on the additional
remote controls pressed for 6 seconds. When
the programming has been transferred, the
red LED indicator will fash three times as a
confirmation.
To reset a remote control to its original
settings, press the buttons S and ALL on
the remote control at the same time for 6
seconds. The LED indicator will fash three
times as a confirmation.
or
or
.
ON
OFF
I or
, for example, or one
ON
(the panel will briefly get dark).
ON
and
Werbung
