Herunterladen Diese Seite drucken

Berner 241996 Originalbetriebsanleitung Seite 18

Vorschau ausblenden Andere Handbücher für 241996:

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
Never break open battery packs and chargers and store only in
dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery
acid wash it off immediately with soap and water. In case of eye
contact rinse thoroughly for at least 10 minutes and
immediately seek medical attention.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
regulations and the directives 2011/65/EU (RoHs),
2006/42/EC, 2004/108/EC and the following harmonized
standards have been used:
EN 60745-1:2009 + A11:2010
EN 60745-2-11:2010
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 50581:2012
Künzelsau, 2015-03-16
Armin Hess
Chairman of the Management Board
Authorized to compile the technical fi le
Berner Trading Holding GmbH
Berner Straße 6
D-74653 Künzelsau
SPECIFIED CONDITIONS OF USE
This sabre saw cuts wood, plastic, and metal. It can cut straight
lines, curves, and internal cut-outs. It cuts pipes and can cut
fl ush to a surface.
Do not use this product in any other way as stated for normal
use.
BATTERIES
New battery packs reach full loading capacity after 4 - 5
chargings and dischargings. Battery packs which have not
been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure to
heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit
situations that cause high current draw, the tool will vibrate for
about 2 seconds and then the tool will turn OFF.
To reset, release the trigger.
Under extreme circumstances, the internal temperatur of the
battery could become to high. If this happens, the battery will
shut down.
Place the battery on the charger to charge and reset it.
For an optimum life-time, after use, the battery packs have to
be fully charged.
445 335 - Berner-BACRS-1_18V.indd 17
445 335 - Berner-BACRS-1_18V.indd 17
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Use only Berner accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Berner service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the ten-digit No. as well as the machine type printed on
the label and order the drawing at Berner.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine.
Please read the instructions carefully before
starting the machine.
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose of electric tools together with
household waste material.
Electric tools and electronic equipment that
have reached the end of their life must be
collected separately and returned to an
environmentally compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
GUARANTEE AND GUARANTEE SERVICE
Each tool, spare part or accessory is consistently checked
before being dispatched from the manufacturing plant. If,
despite this fact, there are any defects, please send the item
directly to our Client Services Headquarters or to the nearest
service repair shop of the fi rm Berner.
The guarantee period is 36 months and starts from the day of
purchase, which must be proved by the original of the purchase
document. During the guarantee period the producer
guarantees:
• free removal of possible defects;
• free replacement of all damaged parts;
• free professional servicing.
The requirement is that these are material and/or
manufacturing defects and that there has not been any
inappropriate operation [of the machine]. Furthermore, only
original accessory parts may be used, which Berner has
expressly identifi ed as suitable for the operation with Berner
machines.
17
ENGLISH
22.07.2015 14:21:05
22.07.2015 14:21:05

Werbung

loading

Diese Anleitung auch für:

Bacrs-1 18v