Panasonic TX-42MZW984 Bedienungsanleitung Seite 13

Select the language
Select your country
To continue using Voice Guidance, after selecting
≥
your country, press [5] (numeric button). Make
settings for [Accessibility].
Select [Home]
Select [Home] for use in a home viewing environment.
[Shop] is for shop display.
≥
To change the viewing environment later on, the set
≥
will need to have all settings initialised by accessing
[Shipping Condition].
Set up the network connection
Depending on the country you select, select your
≥
Region or store the Child Lock-PIN number ("0000"
cannot be stored).
Tick the TV signal mode to tune, and then select
[Start Auto Setup]
Setup screen varies depending on the country and the
≥
signal mode you select.
[DVB-S Antenna Setup]
≥
Ensure the satellite connections are completed (p. 8)
and select the tuner mode ([Dual Tuner] / [Single
Tuner]).
[DVB-C Network Settings]
≥
Normally set [Frequency] and [Network ID] to [Auto].
If [Auto] is not displayed or if necessary, enter
[Frequency] and [Network ID] specified by your cable
provider with numeric buttons.
Auto Setup is now complete and the TV is
ready for viewing.
If tuning has failed check the Satellite cable, RF cable,
and the network connection, and then follow the on-
screen instructions.
<Note>
The TV goes into Standby mode when no operation is
≥
performed for 4 hours if [Auto Standby] in the Timer
menu is set to [On] (factory setting).
The TV goes into Standby mode when no signal is
≥
received and no operation is performed for 10 minutes
if [No signal Power off] in the Timer menu is set to [On]
(factory setting).
≥ To retune all channels
[Auto Setup] in [Tuning Menu] ([Setup] menu)
To add the available TV signal mode later
≥
[Set up TV Signals] ([Setup] menu)
≥ To initialise all settings
[Shipping Condition] in [System Menu] ([Setup]
menu)
FAQs
Before requesting service or assistance, please follow
these simple guides to solve the problem.
For details, refer to [eHELP] (Support > FAQs).
≥
It takes several seconds to display the image after
turning the TV on
≥ When turning the TV on, the panel adjustment is
performed. It is not a malfunction.
The TV does not switch on
≥ Check the mains lead is plugged into the TV and the
mains socket.
The TV goes into Standby mode
Auto power standby function is activated.
≥
The remote control does not work or is intermittent
Are the batteries installed correctly?
≥
Has the TV been switched on?
≥
The batteries may be running low. Replace them with
≥
new ones.
≥ Point the remote control directly at the TV's remote
control signal receiver (within about 7 m and a
30 degree angle of the signal receiver).*
Situate the TV away from sunshine or other sources of
≥
bright light so they do not shine on the TV's remote
control signal receiver.*
≥ Is the remote control mode wrong?
≥ If you are trying to use voice controls, is the remote
control registered (paired) with the TV?
≥ If the solutions above do not fix the problem,
deregister (unpair) the remote control, then
register (pair) it again.
control does not respond" (p. 10)
When infrared communication is used
No image is displayed
Check the TV is turned on.
≥
Check the mains lead is plugged into the TV and the
≥
mains socket.
Check the correct input mode is selected.
≥
Is [Luminance Level], [Contrast], [Brightness] or
≥
[Colour] in the Picture menu set to the minimum?
Check all required cables and connections are firmly
≥
in place.
Press and hold the Power On / Off switch on the TV
≥
for 5 or more seconds and then release your finger to
reboot the TV.
An unusual image is displayed
This TV has a built-in Self Test. Makes a diagnosis of
≥
picture or sound problems.
[TV Self Test] ([Help] menu)
(p. 11)
(p. 10)
"When the remote
English
13