Werbung
Verfügbare Sprachen
Verfügbare Sprachen
OFFICE MODE (OF)
Startup and Reset – must be carried out after a long power cut or at
first time use.
A Startup/Reset procedure has to be performed to initiate the correct
mode and function of the thermostat.
IMPORTANT: there are two different startup sequences
1) If °C-17-rE is flashing in the display: go to procedure A.
2) If HO is flashing in the display: go to procedure B.
The procedure must be completed in one continuous sequence to be
valid. Should the procedure be performed incorrectly or fail, switch off
the heater and start a new reset procedure.
Startup procedure A – if the thermostat has been connected and
switched on beforehand:
Startup procedure B – if the thermostat has never been switched on
since leaving the factory:
28
On switching heater on, the sequence
°C – 17 – rE - will flash in the display.
This means that the thermostat has
been disconnected for a long period
and needs to be restarted.
To set the thermostat back to the fac-
tory default, switch off the heater using
the main power switch.
Press
and hold in and at the same
time switch on using the main power
switch.
Continue to press
until rE flashes in
the display, then release
.
After a few seconds HO will flash in
the display.
You can choose between the modes HO
(Home), OF (Office) and CA (Cabin) by
pressing the
or
key.
Confirm your choice by holding in the
key for more than 5 seconds.
22 (°C) will flash. Select your preferred
comfort temperature.
Confirm by holding in the
key for
more than 5 seconds.
If you do nothing, 22 (°C) will be
stored automatically after 7 seconds.
When the heater is switched on, HO
(Home mode) will flash in the display.
You can select between modes HO, OF
(Office) and CA (Cabin) by pressing the
or
key.
Confirm your choice by pressing in
key for more than 5 seconds.
22 (°C) will flash. Select your preferred
comfort temperature.
Confirm by pressing in the
key more
than 5 seconds.
If you do nothing, 22 (°C) will be
stored automatically after 7 seconds.
Starting the temperature cutback function
Cutback indicator
Working overtime
To cancel a period of temperature cutback
GB/AU
Three hours before you usually leave
the office press down on
for 5
seconds (e.g. At 14:00 –
2 PM – press
for 5 seconds).
h (hours) will flash for three seconds,
then 12 (hours) will flash. Select the
number of hours you want cutback to
be active by pressing
or
(NB! Cutback will start after three
hours.) Confirm by pressing
d (day) will be displayed steadily for
three seconds. Then a random number
will flash (1 = Monday, 2 = Tuesday,
etc). Select the correct day using
and confirm by pressing
°C will flash three times and then 17
(°C) will flash continuously. With the
or
key select your preferred
cutback temperature.
Confirm by pressing
key briefly.
Comfort temperature will continue for
three hours before the cutback starts
automatically.
(E.g. At 17:00 – 5 PM – the cutback
period will start and the LED (1) will
flash slowly.)
During the cutback period the LED (1)
will flash slowly. When it is lit stead-
ily, it indicates that cutback function is
not currently active but will start at the
appropriate time of the evening.
Press
for 5 seconds. The set
comfort temperature will show in the
display. The LED above the
will light steady while the LED above
the
key will continue flashing. You
now have a temporary comfort period
lasting five hours.
Hold down on
and press once on
to override the currently active period
– or the next period of temperature
cutback. The lamp is lit steadily for
the period in question. Temperature
cutback periods will resume as usual
from the following period.
.
briefly.
or
briefly.
key
Werbung
