Werbung
Verfügbare Sprachen
Verfügbare Sprachen
HOME MODE (HO)
Startup and Reset - must be carried out after a long power cut or at
first time use.
A Startup/Reset procedure has to be performed to initiate the correct
mode and function of the thermostat.
IMPORTANT: there are two different startup sequences
1) If °C-17-rE is flashing in the display: go to procedure A.
2) If HO is flashing in the display: go to procedure B.
The procedure must be completed in one continuous sequence to be
valid. Should the procedure be performed incorrectly or fail, switch off
the heater and start a new reset procedure.
Startup procedure A – if the thermostat has been connected and
switched on beforehand:
Startup procedure B – if the thermostat has never been switched on
since leaving the factory:
26
On switching heater on, the sequence
°C – 17 – rE - will flash in the display.
This means that the thermostat has
been disconnected for a long period
and needs to be restarted.
To set the thermostat back to the fac-
tory default, switch off the heater using
the main switch.
Press and hold in
and then switch on
using the main power switch.
Continue to press
until rE flashes in
the display, then release
.
After a few seconds HO will flash in
the display.
You can choose between the modes
HO, OF (Office) and CA (Cabin) by
pressing the
or
key.
Confirm your choice by pressing in the
key for more than 5 seconds.
22 (°C) will flash. Select your preferred
comfort temperature.
Confirm by pressing in the
key for
more than 5 seconds.
If you do nothing, 22 (°C) will auto-
matically be stored after 7 seconds.
When the heater is switched on, HO
(Home mode) will flash in the display.
You can select between modes HO, OF
(Office) and CA (Cabin) by pressing the
or
key.
Confirm your choice by pressing in
key for more than 5 seconds.
22 (°C) will flash. Select your preferred
comfort temperature.
Confirm by pressing in the
key more
than 5 seconds.
If you do nothing, 22 (°C) will auto-
matically be stored after 7 seconds.
Start nighttime temperature cutback
This will be repeated for the same period every night.
Start daytime temperature cutback
number of hours you have chosen. This will be repeated at the same
times from Monday to Friday, leaving Saturday and Sunday unaffected.
GB/AU
At the time you wish temperature cut-
back to start, press
for 5 seconds.
h (hours) will flash 3 times and then
07 will flash continuously.
With the
or
key select the
number of hours you want the cutback
to last.
Confirm by pressing the
key briefly.
°C will flash 3 times and then 17 (°C)
will flash continuously.
Using the
or
key select the
cutback temperature.
Confirm by pressing
key briefly.
The green lamp (4) will now flash
slowly to indicate that temperature
cutback is active.
The temperature is reduced for the
number of hours you have chosen.
At the time you wish temperature cut-
back to start, press
for 5 seconds.
h (hours) will flash 3 times and then
05 will flash continuously.
Using the
or
key, select the
number of hours you want the tem-
perature cutback to last.
Confirm by pressing the
key briefly.
d will flash 3 times and then a random
number.
Using the
or
key, enter the
correct day of the week (Monday = 1,
etc.).
Confirm by pressing the
key briefly.
°C will flash 3 times and then 17 (°C)
will flash continuously.
With
or
key select your pre-
ferred cutback temperature.
Confirm by pressing
key briefly.
The green lamp (1) will now flash
slowly to indicate that temperature
cutback is active.
The temperature is reduced for the
Werbung
