nedis PAAC10BK Kurzanleitung Seite 2

2. Specification
Product name: Rechargeable Air Compressor
Product model: PAAC10BK
Product size: 157*64*44mm
Weight: 420g
Inflation pressure: 10.3 bar (max)
No-load flow: 15-18L/min
Working temperature: -10° ~ 45°C
Battery capacity: 14.8Wh
Charging input: 5V/2A
Charging time: 2~3h
3. Illustration (image A)
LED light
1
Hose connector
2
Type-c charging port
3
Unit
4
Measured pressure
5
Mode
6
4. How to use
4.1 Charging Method (image B)
Green light: 60~100%
r
t Red light: 0~30%
The USB charger is recommended to use 5V / 2A. Use the Type-C charging cable
to connect the air pump and power adapter (sold separately) for charging.
Charging status: battery indicator flashes.
Full state: the battery indicator is green and does not flash. The product
cannot be used during charging.
4.2 Power On/Off
Switch on When starting, press the power button for 3 seconds.
Shutdown When shutting down, press the power button for 3 seconds.
4.3 Application scenario switching
Short press mode selection key e,you can choose 5 inflatable scene modes.
They are:
Scene mode
Car mode
Motorcycle mode
Bicycle mode
Custom mode
Ball mode
4.4 Unit switching
Short press the unit switch key 8, you can switch the air pressure display
unit. The unit conversion formula is shown below:
1PSI = 6.89KPA
4.5 Preset pressure value
Short press +/− button: Adjust the preset pressure value. Long press +/−
button: can quickly adjust the preset pressure value.
Note: The scene switch and preset pressure value are automatically saved
by the software. You only need to switch the scene for the next use, and the
preset pressure is automatically set.
4.6 Hose connection (image C)
The connection of the hose is shown in the following figure:
Schrader valve
y
4.7 Start inflation
Short press the inflation switch
the real-time air pressure value
generated during inflation, and the hose produces high temperature during
long-term work. Avoid prolonged contact with hose and hose joints by
hand .
2
4.8 Stop inflation
Short press the inflation switch
When switching scene modes or preset pressure values, the screen will flash
three times for the currently set scene mode and pressure value, will be
displayed after flashing real-time pressure value.
4.9 LED Lighting
Long press LED
Press and hold the LED light button
4.10 Measuring pressure
After switching on, connect the air pipe to the measured object, and the
measured pressure value
4.11 Reset
After switching on, when the measured pressure value is not zero, press the
preset +/– key for 3 seconds at the same time to enter auto clear.
Note: The product has been cleared from the factory. When the difference
in altitude or the sensor tolerance shows that the measured pressure is not
zero, manual clearing can improve the accuracy of pressure detection. Do not
connect inflatable objects when clearing
Reference value
1BAR = 100KPA
Presta Valve
u
to turn on LED lighting.
8
5 shows the current pressure value.
Battery level
7
LED torch unit switch
8
Preset −
9
Power on/off
q
Preset +
w
Application scenario
e
2.4 bar
2.8 bar
2.6 bar
6.8 bar
0.5 bar
1Kg/cm
2
q to start inflation. The digital display of
changes during inflation. Noise will be
5
to stop inflation manually.
q
to turn off the LED light.
8
Adjustable range
= 98KPA
Ball needle nozzle
i
0-4.4 bar
0-3.7 bar
0-10.3 bar
0-10.3 bar
0-1.0 bar