Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Paul Hochköpper GmbH & Co. KG
Postfach 1727 • D-58467 Lüdenscheid • Tel.: +49 (0)2351 185-0 • Fax: +49 (0)2351 27666 • e-mail: peha@peha.de • Internet: www.peha.de
6. Operation and functions
6.1 Operating
The receiver is operated with Easyclick transmitters (radio
signal). Before use, the transmitters must be assigned to
the receiver (max. 32 receivers). The receiver's Function 1
is preset after assigning a transmitter to the receiver. It can
be changed by function programming. Every transmitter
can control an unlimited number of receivers.
6.2 General functions
Function
Description
Memory
The current dimming value is saved.
When switched on, the illumination is adju-
Soft start
sted to the saved dimming value (memory).
If the illumination was switched on, it is star-
Memory
ted by using the soft start function.
after
If the illumination was switched off, it re-
blackout
mains switched off.
Note: After a blackout, the last saved dimming value (me-
mory) is still available.
6.3 Easyclick wall transmitters
Button O
Button I
6.3.1 Function 1 (Two-button operation with memory)
Wall transmitter
Function
Press button I briefly
Switch on with soft start
Press button O briefly
Switch off with memory
Press button I long
Dim lighting up
Press button O long
Dim lighting down
Press button long
Dimming process stops
and release
(memory)
Note: Standard function after assigning a transmitter!
6.3.2 Function 2 (Two-button operation)
Wall transmitter
Function
Press button I briefly
Switch on with parameter
Press button O briefly
Switch off
Press button I long
Dim lighting up
Press button O long
Dim lighting down
Press button long
Dimming process stops
and release
Parameters
1
Brightness 100%
2
Brightness 10%
3
Brightness 25%
4
Brightness 40%
5
Brightness 55%
6
Brightness 70%
7
Brightness 85%
Note: The brightness of the lighting after switch-on can be
established by setting parameters.
6.3.3 Function 3 (Switch on / off)
Wall transmitter
Function
Press button I
Switch on
Release button O
Switch off
Parameters
1
Switch on with soft start
2
Switch on with maximum brightness
451 FU-BEP DAB (Rev05_090220)
All manuals and user guides at all-guides.com
6.3.4 Function 4 (Dim up / down)
Wall transmitter
Press button I long
Press button O long
Press button long
and release
6.3.5 Function 5 (One-button operation with memory)
Wall transmitter
Press button briefly
Press button long
Press button long
and release
Parameters
1
Button O is activated
2
Button I is activated
3
Button I and button O are activated
6.3.6 Function 6 (Stairwell light)
Wall transmitter
Button O
Press button I
or O briefly
Button I
Parameters
1
2 min running time
2
1 min running time
3
5 min running time
4
10 min running time
5
20 min running time
6
30 min running time
7
60 min running time
8
120 min running time
Note: After the running time (parameter) has elapsed, the
brightness of the lighting is reduced by 50 % for a period
of 30 s (switch-off warning). After this, the illumination is
turned off.
6.3.7 Function 7 (Light scenes)
Wall transmitter
Press button O briefly
Press button O long
Press button I briefly
Press button I long
Parameters
1
button O = light scene A, button I = light scene B
2
button O = light scene C, button I = light scene D
Application example: light scene
A light scene can be adjusted by using a transmitter and
an available light control (various receivers with assi-
gned transmitters).
Programming
Assign the transmitter to each receiver, program
function 7 and set parameter.
Store light scene (A-D)
• Switch on the required light scene (receivers).
• Press button I or O of the transmitter for longer than 2s.
As a confirmation, the lighting switches off and on.
Select light scene (A-D)
Press briefly the button I or O of the transmitter.
126308-03
Function
Dim lighting up
Dim lighting down
Dimming process stops
(memory)
Function
Switch on with soft start or
switch off with memory
Dim up or down
Dimming process stops (memory)
Function
Switch on with max. brightness
and running time (parameter)
Function (parameter)
Switch on light scene A/C
Store light scene A/C
Switch on light scene B/D
Store light scene B/D
7. Troubleshooting & remedies
7.1 New system or existing system
• Check circuit breaker and power supply
(electrician only).
• Check connected electrical loads and connection cables
(electrician only).
• Check the system's surroundings for changes that could
cause interference (e.g. metal cabinets, furniture or walls
which have been moved).
• If the receiver operates at a reduced distance from the
transmitter, the radio signal was encountering interference
or it was operating outside the transmission range.
• Use the receiver at a better location.
• Delete all transmitters and reprogram the receiver.
7.2 Receiver switches by itself
• This may be caused by operation of an external trans-
mitter that was coincidentally assigned to the receiver.
• Delete all transmitters and reprogram the receiver.
7.3 Radio signal range limitations
• Use of the receiver in the vicinity of metal objects or
materials with metal components. Maintain a distance
of at least 10 cm.
• Moist materials.
• Devices which emit high-frequency signals (e.g. audio
and video systems, computers, electronic ballasts
in light fixtures). Maintain a distance of at least 0.5 m.
7.4 Contact
Telephone:................ +49 (0)2351 185-0
Fax:.......................... +49 (0)2351 27666
Internet:.................... www.peha.de/contact.aspx
E-mail:...................... peha@peha.de
8. Conformity declaration
PEHA products may be sold and operated in EU countries
as well as in CH, IS and N. PEHA herewith declares that
the receiver (451 FU-BEP DAB) is in compliance with the
fundamental requirements and other relevant provisions of
R&TTE Directive 1999/5/EC. The conformity declaration is
available on the Internet at the following address:
www.peha.de/ServiceDownloads.aspx.
GB - 2
Werbung
