Elektra Beckum BAS 315/4 GWN 55 Betriebsanleitung Seite 9

Contents
1 General 2.6 Safety Information
1.1 , Specifications 2.7 0ther Information
1.2 User Responsibility/Warranty 2.8 Electrical Installation
1.3 Final Assembly and Installation 3 Accessories
2 Settings
3.1 Mitre Fence
2.1 Selecting the Correct Blade Speed 3.2 Workstand
2.2 Changing and Setting the Sawblade 4 Bandsaw Blades
2.3 Blade Guiding 5 Electrical Wiring Diagrams
2.4 Setting the Cutting Height
2.5 Saw Table Tilt
6 Spare Parts List/Exploded View Drawing
1 General
1.1 Specifications BAS 315/4 GWN 55 BAS 315/4 GDN 55
Dimensions (Ixwxh) 590x610x1265 mm 590x610x1265mm
Weight with motor 60 kg 60 kg
Table height from floor 480 mm 480 mm
Table height from floor on workstand 1100 mm
1100 mm
Throat width 305 mm 305 mm
Max. cutting height 160 mm 160 mm
Sawblade length 2240 mm 2240 mm
Sawblade width 6-15 mm 6-15 mm
Sawtable tilt to 45° to 45°
Sawtable size 400x548 mm 400x548 mm
Sawblade speeds 370 -
1
- 800 m/min 370 + 800 m/min
Motor capacity PI -0.81 kWSI PI - 0.76 kW SI
P2 - 0.55 kW S1 P2 - 0.55 kW SI
Noise information pursuant to DIN 45635: no-load working
Sound power level 84.1 dB(A) 85.5 dB(A)
Workplace related noise emission value 73.3 dB(A)
79.4 dB{A)
1.2 User ResponsibilityA/Varranty
This appliance will perform in conformity with thedescription contained in the instructions provided. This machine must be checked
periodically. Defective equipment (including power cables) should not be used. Parts that are broken, missing, obviously worn,
distorted or contaminated, should be replaced immediately. Should such repair or replacement become necessary, it is
recommended that only genuine Elektra Beckum replacement parts are used and that such repairs are carried out by qualified
persons approved by Elektra Beckum or its representatives. Failure to comply relieves Elektra Beckum from product liability. The
aforementioned also applies to all accessories offered for this appliance.
This appliance or any of its parts should not be altered or changed from standard specifications. The user of this machine shall
have the sole responsibility for any malfunction which results from improper use or unauthorized modification from standard
specifications, faulty maintenance, damage or improper repair by anyone other than qualified person approved by Elektra
Beckum or its representatives.
Please fill in the warranty registration card and send to the address shown on it. Normal wearing parts and consumables are not
covered by the warranty.
1.3 Final Assembly and Installation
Unpack machine and check for any visible damage which may have occurred
during transport. If a damage is detected notify your dealer immediately.
This machine is shipped partly disassembled. Saw table, rip fence guide and
crank handle have to be installed prior to use.
• Remove the rip fence guide extrusion from the table.
• Place the table onto the upper table trunnion.
• Install to trunnion with 4 each serrated lock washer and hexagon head screw
M 8x16.
• Attach rip fence guide extrusion to table with the four thumb screws.
• Place table insert into the table centre hole (table insert with wide slot for
bevel cuts only).
• Insert cup square neck screw into rip fence guide and secure with washer 0
8.4 and wing nut.
• Attach rip fence extrusion with 2 each cup square neck screw M 6x35,
washer 0 6.4 and knurled nut M 6 to the rip fence guide.
• install crank handle with cap screw M 6x55 and two hex. flat nuts M 6 to the
crank.
After installation adjust the table so that the sawblade runs through the centre
of the table insert's slot.
9