Troubleshooting - Philips S7920 Anleitung

8 After approx. 20 seconds you can move
the attachment to your forehead and start
cleansing this part of your face. Gently move
the brush head from left to right (Fig. 32).
Note: We advise you to not overdo the
cleansing and to not cleanse any zone longer
than 20 seconds.
9 After the treatment, rinse and dry your face.
Your face is now ready for the next step of your
daily skincare routine.
10 Clean the attachment after use (see ‚Cleaning
and maintenance').
Cleaning and maintenance
Cleaning the shaver under the tap
Clean the shaver after every shave for optimal
performance. As an extra reminder, the notification
symbol on the shaver lights up once every
6 shaves to tell you to clean the shaver.
Warning: Be careful with hot water. Always
check if the water is not too hot, to prevent
your hands from getting burnt.
Caution: Never dry the shaving unit with
a towel or tissue, as this may damage the
shaving heads.
1 Switch on the shaver.
2 Rinse the shaving unit under a warm tap (Fig.
20).
Note: You can also clean the shaving unit with
the cleaning brush supplied (Fig. 33).
3 Switch off the shaver.
4 Pull the shaving head holder off the bottom part
of the shaving unit and rinse or brush the hair
chamber to remove any excess hairs (Fig. 34).
Let it dry.
5 Rinse the shaving head holder under a warm tap.
Note: You can also clean the shaving head
holder with the cleaning brush supplied.
6 Carefully shake off excess water and let the
shaving head holder dry.
7 Reattach the shaving head holder to the bottom
part of the shaving unit (‚click') (Fig. 35).
Cleaning the click-on attachments
Caution: Never dry the beard styler
attachment with a towel or tissue, as this may
damage the trimming teeth.
Cleaning the beard styler attachment
Clean the beard styler attachment every time you
have used it.
1 Pull the comb off the beard styler attachment.
Note: Grab the comb in the centre to pull it off
the beard styler attachment. Do not pull at the
sides of the comb (Fig. 26).
2 Switch on the appliance.
3 Rinse the beard styler attachment and the
comb separately under a warm tap for some
time.
4 After cleaning, switch off the appliance.
5 Carefully shake off excess water and let the
beard styler attachment and comb dry.
Tip: For optimal performance, lubricate the
teeth of the attachment with a drop of sewing
machine oil every six months.
Cleaning the cleansing brush attachment
Clean the cleansing brush attachment every time
you have used it.
1 Make sure the appliance is switched off.
2 Detach the brush head from the brush base
(Fig. 36).
3 Clean both parts thoroughly with warm water
and mild soap.
4 Dry the cleansing brush attachment with a
towel. Reattach the brush head to the brush
base.
Storage
Note: We advise you to let the shaver and its
attachments dry before you put the protection cap
on the attachment and store the shaver in the pouch.
-
Store the shaver in the pouch supplied.
-
Put the protection cap on the cleansing brush
attachment to protect it from dirt accumulation.
Replacement
Replacing the shaving heads
For maximum shaving performance, we advise you to
replace the shaving heads every two years (Fig. 42).
Always replace the shaving heads with original
Philips shaving heads (see ‚Ordering accessories').
1 Switch off the appliance.
2 Pull the shaving head holder off the bottom part
of the shaving unit.
3 Turn the retaining rings anticlockwise and
remove them (Fig. 37).
4 Remove the shaving heads from the shaving
head holder and throw them away (Fig. 38).
5 Place new shaving heads in the holder (Fig. 39).
Note: Make sure the notches on both sides
of the shaving heads fit exactly onto the
projections in the shaving head holder.
6 Place the retaining rings back onto the shaving
heads and turn them clockwise (Fig. 40).
-
Each retaining ring has two recesses that fit
exactly into the projections of the shaving head
holder. Turn the ring clockwise until your hear a
click to indicate that the ring is fixed (Fig. 41).
- Note: Hold the shaving head holder in your
hand when you reinsert the shaving heads and
reattach the retaining rings. Do not place the
shaving head holder on a surface when you do
this, as this may cause damage.
7 Attach the shaving head holder to the bottom
part of the shaving unit ('click') (Fig. 35).
Replacing the cleansing brush head
The brush head should be replaced every 3 months
or earlier if the brush hairs are deformed or damaged
(see ‚Ordering accessories').
Ordering accessories
To buy accessories or spare parts, visit
www.shop.philips.com/service or go to your
Philips dealer. You can also contact the Philips
Consumer Care Centre in your country (see the
worldwide guarantee leaflet for contact details).
The following accessories and spare parts are
available:
-
HQ8505 adapter
- SH70 Philips shaving heads
-
HQ110 Philips shaving head cleaning spray
-
RQ111 Philips beard styler attachment
- SH575 Philips cleansing brush attachment
-
SH560 Philips cleansing brush attachment head
- Note: The availability of the accessories may
differ by country.
Recycling
- This symbol means that this product shall not
be disposed of with normal household waste
(2012/19/EU) (Fig. 43).
-
This symbol means that this product contains a
built-in rechargeable battery which shall not be
disposed of with normal household waste
(Fig. 44) (2006/66/EC). We strongly advise you
to take your product to an official collection
point or a Philips service centre to have a
professional remove the rechargeable battery.
- Follow your country's rules for the separate
collection of electrical and electronic products
and rechargeable batteries. Correct disposal
helps prevent negative consequences for the
environment and human health.
Removing the rechargeable battery
Warning: Only remove the rechargeable
battery when you discard the shaver. Before
you remove the battery, make sure that the
shaver is disconnected from the mains and
that the battery is completely empty
Warning: Take any necessary safety
precautions when you handle tools to open
the shaver.
1 Check if there are screws in the back of the
shaver or in the hair chamber. If so, remove
them.
2 Remove the outer panels of the shaver with
a screwdriver or other tools. If necessary, also
remove additional screws and/or parts until
you see the printed circuit board with the
rechargeable battery.
3 Remove the rechargeable battery.
Guarantee and support
If you need information or support, please visit
www.philips.com/support or read the separate
worldwide guarantee leaflet.
Guarantee restrictions
The shaving heads (cutters and guards) are
not covered by the terms of the international
guarantee because they are subject to wear.

Troubleshooting

This chapter summarizes the most common
problems you could encounter with the appliance.
If you are unable to solve the problem with the
information below, visit www.philips.com/support
for a list of frequently asked questions or contact
the Consumer Care Center in your country.
Problem Possible cause Solution
I cannot You have not The app is available
connect downloaded for iPhone 4S
the shaver. the app. (or higher) which
is running iOS7 or
higher.
Make sure the shaver
is switched on.
Try restarting your
smartphone and try
again.
Make sure you
open the app.
The Make sure your
smartphone smartphone has
cannot find the Bluetooth 4.0 or
shaver. higher.
Make sure
Bluetooth is
enabled on the
shaver and the
smartphone.
Make sure the
shaver is charged.
I want to You can also use
use the the shaver without
shaver the app. However,
without only when you use
the app. the app together
with the shaver,
the app is able to
provide tips and
advice based on
your usage. With
the app you can set
your sensitive shave
settings. The app
also reminds you
when you need to
replace the shaving
heads, to clean the
shaver, etc.