Schartec DC660 Bedienungsanleitung Seite 4

ENGLISH
Schartec roller-shutter wireless wall switch FW1
Frequency: 433.92 MHz Rolling-Code
Transmitting power: 10 mW
Channels: 1
Battery: 2x 3V(CR2430) button cell lithium
Working temperature: -20°C to +50°C
Article number: ST701019
Model number: DC660
• Keep wireless wall switchs out of reach of children.
• Wireless wall switches may only be operated by persons who are familiar with the system and have been
instructed in their function.
• Use the wireless wall switch only when you are in sight of the roller-shutter.
• Coding in wireless wall switches must always be carried out within the vicinity of the operator. Use only original parts.
• Protect wireless wall switchs from rain, snow, sunlight or dust, otherwise the function of the transmitter may be impaired
• In order to change the battery, carefully remove the cover to the wireless wall switch.
Program the wireless wall switch to a roller shutter/awning motor or radio receiver:
1. Carefully remove the cover to the wireless wall switch.
2. Switch on the voltage of the roller shutter/awning motor or receiver.
3. Within 5 seconds of turning on the power, the motor will beep 3 times, press the Modus button on the wireless wall switch once (it will beep and the motor will move up and down briefly); then
press the Modus button again (after the brief movement), it will beep again and the motor will move up and down briefly.
4. Immediately afterwards, press the Up button, the signal tone sounds 3 times and the motor moves up and down briefly. The wireless wall switch is now taught-in.
5. To change the buttons direction, repeat the procedure, but instead of pressing the Up button, press the Down button. Now the Up and Down buttons are reversed.
Programming on the Schartec Tube F roller shutter motor
Switch on voltage
Programming additional wireless wall switches
1. Press the Modus button once on the wireless wall switch that has already been taught-in (a signal tone sounds and the motor moves up and down briefly).
2. Then press the Modus button again (after the short movement), a signal tone sounds again and the motor moves up and down briefly.
3. Within 3 seconds, press the Modus button on the new wireless wall switch once; the beep sounds 3 times and the motor moves up and down briefly. The new wireless wall switch is now taught-in.
4. The new wireless wall switch has now taken over the coding from the already taught-in wireless wall switch. You can program up to ten wireless wall switches per motor/receiver. When you teach
in the eleventh wireless wall switch, the first one is deleted.
For "older" versions of the Schartec roller shutter motor, the back-and-forth movement of the motor when teaching the wireless wall switch is omitted, but the process is exactly the
Schartec hereby declares that the wireless wall switch FW1 complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following Internet address: www.schartec.de
As a dealer for the distribution of electronic, battery-operated devices, we are obliged by law to inform our customers about the following: Electrical and electronic devices, as well as batteries, must not be disposed of as house-
Press Mode Press Mode
button 1x button 1x
3 beeps
Beep and short
motor movement
Simplified EU Declaration of Conformity (CE)
Information about battery regulation
hold or residual waste, but must be taken to appropriate battery acceptance and collection points.
The complete version of the battery law can be found here:
http://www.gesetze-im-internet.de/bundesrecht/battg/gesamt.pdf
a trademark of bau-shop-24 GmbH
Fritz-Müller-Strasse 115
WEEE Reg. Nr.: DE90317979
BattG Reg. Nr.: DE50302356
Product description
Up
Time setting
Stop
This operation deletes all stored
transmitters and Schartec Time F is
programmed in
Press Up
button 1x
Beep and short
Press Down
motor movement
button 1x
NOTE:
same!
SCHARTEC
73730 Esslingen
Germany
4
Up: Move motor upward/increase time
Down: Drive motor downward/reduce time
Stop: Motor stoppen/ Timer Menü verlassen
Time setting: Set time/check time setting (press and
hold for 5 sec.)
Time confirmation: Confirm time and save
Mode: Change mode
Down
Time confirmation
Monday Wednesday
Sunday Tuesday
Mode
Manual
Automatic
Freely selectable
Battery status
Hours
The Up button moves
the motor clockwise
clockwise
OK
The Down button moves
the motor clockwise
clockwise
OK
V. 231005
Friday
Thursday Saturday
Up
Time-Mode
Down
Minutes