Werbung
„midi-ou
The fifth setting clock.divider out is used to configure the clock-divider of the outgoing analog trigger-clock.
„midi-ou
The sixth setting pulse.length is used to configure the pulse-length of the outgoing analog trigger-clock. The smallest pulse-
length is really very short and the longest really very long. Some sequencers might have problems with that. If so, please select a
longer/shorter pulse.length.
The settings for the analog output (trigger.type out, clock.divider out und gate.length) can be changed without losing
synchronisation, while the masterclock is running.
In addition to the clock-signal, start-/stop-signals from the masterclock are detected and processed, but it it also possible to
send start-/stop-signals manual.
If you hold the left button, all LEDs glow. The middle button can now be used to manually perform a stop and the right button, to
perform a start.
2. Trigger-tool:
The audiowerkstatt trigger2midi2trigger v2 can also be used as a tool for analog-trigger-signals, if it isn't used as a converter.
„midi-ou
In this case, the setting input has always to be set to trigger .
„S-Trigg
" zu „V- „S-Trigg
a) S-trigger to v-trigger -converter:
„midi-ou
"-Buchse
If trigger.type in is set to s-trigger and trigger.type out to v-trigger , you get a S-trigger to v-trigger -
converter, The ring of the start/stop -jack is input and the tip is output.
Normal insert-cables can be used to connect the analog input/output.
„S-Trigg
" zu „V- „S-Trigg
b) V-trigger to s-trigger -converter:
„midi-ou
"-Buchse
If trigger.type in is set to v-trigger and trigger.type out to s-trigger , you get a V-trigger to s-trigger -
converter, The ring of the start/stop -jack is input and the tip is output.
Normal insert-cables can be used to connect the analog input/output.
c) Analog clock-divider:
„midi-ou
"-Buchse
If clock-divider in is set to 1/32 , you get an analogen clock-divider. The ring of the clock -jack is input and the tip is
„midi-ou
output. With the setting clock-divider out you can now set the divider: 1/32 leaves the clock as it is, 1/16 makes half
„midi-ou "-Buchse
speed, 1/8 makes quarter-speed and 1/4 make it run 1/8th of the speed..
„midi-ou
"-Buchse
With trigger.type in and trigger.type out , the trigger-types can be set and with pulse.length , the length of the clock-
pulse can be adjusted..
Normal insert-cables can be used to connect the analog input/output.
d) Analog clock-multiplier:
„midi-ou
"-Buchse
If clock-divider in is set to 1/4 , you get an analogen clock-multiplier. The ring of the clock -jack is input and the tip is
„midi-ou
output. With the setting clock-divider out you can now set the factor to multiplie: 1/4 leaves the clock as it is, 1/8 makes
„midi-ou
it run double speed, 1/16 makes four times higher speed and 1/32 make it run 8 times faster.
„midi-ou
"-Buchse
With trigger.type in and trigger.type out , the trigger-types can be set and with pulse.length , the length of the clock-
pulse can be adjusted..
Normal insert-cables can be used to connect the analog input/output.
"-Buchse
"-Buchse
"-Buchse
" zu „V-
„midi-ou
"-Buchse
„midi-ou
„midi-ou
"-Buchse
" zu „V-
„midi-ou
"-Buchse
„midi-ou
„midi-ou
"-Buchse
„midi-ou
"-Buchse
"-Buchse
„midi-ou "-Buchse
„midi-ou
"-Buchse
„midi-ou "-Buchse
"-Buchse
"-Buchse
„midi-ou
"-Buchse
„midi-ou
"-Buchse
"-Buchse „midi-ou
"-Buchse
"-Buchse „midi-ou
"-Buchse
„midi-ou
"-Buchse
„midi-ou
"-Buchse
„midi-ou
"-Buchse „midi-ou
„midi-ou
"-Buchse „midi-ou
„midi-ou
"-Buchse
„midi-ou
„midi-ou
"-Buchse
„midi-ou
"-Buchse
„midi-ou "-Buchse
„midi-ou
"-Buchse
"-Buchse
"-Buchse
"-Buchse
„midi-ou "-Buchse
Werbung
