Werbung
audiowerkstatt trigger2midi2trigger v2
The audiowerkstatt trigger2midi2trigger v2 converts analog trigger-clock-signals to MIDI-clock-signals and vice versa. It can
also be used as an analog trigger-tool.
Connectors:
9-12v:
Input for connecting a power supply (9-12V AC or DC (polarity doesn't matter)).
midi-in:
Input for connecting the output of the MIDI-master.
midi-out:
Output for connecting the input of the MIDI-slave.
clock:
Stereo-Jack for analog trigger-clock-signals (output is pin und input is ring of the jack).
start/stop:
Stereo-Jack for analog start/stop-signals (output is pin und input is ring of the jack).
Function of the buttons and LEDs:
The LEDs display the settings. The LEDs of the setting that is selected for setup are flashing.
The left button is used to select, which setting you are editing, with the other two buttons, you can adjust the value.
If you hold the left button, all LEDs glow. The middle button can now be used to manually perform a stop and the right button, to
perform a start.
All settings will be saved and restored at startup.
Applications:
1. Trigger-clock- to MIDI-clock-converter and MIDI-clock- to trigger-clock-converter:
In this use, there is always a MIDI-clock-signal (incl. start/stop) sent at the "midi out"-jack and at the tip of the "clock"-phone-
jack, an analog trigger-clock-signal (v-trigger: 0v/5v pulse; s-trigger open/closed) is sent. The tip of the "start/stop"-phone-jack
is if v-trigger is used 5v while the masterclock is running and 0v while the masterclock is paused and if s-trigger is used it is
„midi-ou
"-Buchse
closed while the masterclock is running and open while the masterclock is paused .
„midi-ou
With the first setting input , the clock-source is selected. If midi is selected, the, at the midi-in incoming midi-clock (incl.
start/stop) is used as clock-source. If trigger is selected, the, at the ring of clock incoming analog-pulse will be used as
clock-source and the, at the ring of start/stop incoming signal will be used as source for start/stop.
Normal insert-cables can be used to connect the analog inputs/outputs. If only the analog outputs are used, normal phone-jack-
cables (mono or stereo) can be used.
„midi-ou
The second setting trigger.type in is used to select, if the incoming analog trigger-clock is a s-trigger - or a v-trigger -
signal.
„midi-ou
"-Buchse
If midi is used as clock-source, this setting has no effect.
„midi-ou
The third setting trigger.type out is used to select, if the outgoing analog trigger-clock is a s-trigger - or a v-trigger -
signal.
„midi-ou
The fourth setting clock.divider in is used to configure the clock-divider of the incoming analog trigger-clock. If the clock is
running at a speed og 1/16th, it is set to 1/16 , if the speed of the clock is a quarter-note, you set it to 1/4 .
If this is not set up propperly, the generated clock will be in sync, but not in the right way. It would run half speed or double or
something like that.
„midi-ou
"-Buchse
If midi is used as clock-source, this setting has no effect.
– trigge
„midi-ou
"-Buchse
„midi-ou
"-Buchse
„midi-ou
"-Buchse
"-Buchse
"-Buchse
"-Buchse
„midi-ou
"-Buchse
"-Buchse
„midi-ou
"-Buchse
„midi-ou
„midi-ou
"-Buchse
"-Buchse
„midi-ou
"-Buchse
„midi-ou
"-Buchse
„midi-ou "-Buchse
„midi-ou
"-Buchse
„midi-ou
"-Buchse
Werbung
