SUHNER MACHINING WS Original Bedienungsanleitung Seite 18

1. N
1.1 g
enerAl nOtes On sAFety
This operation manual is applicable for the partly com-
pleted machinery WS.
The partly completed machinery may only be han-
dled by personnel who are qualified.
The work area must be demarcated in such a way
that no hazards can escape to the outside. It.must be un-
obstructed and secured against unauthorized access.
1.2 u
se FOr purpOses FOr which it is intended
The partly completed machinery is designed for the au-
tomated grinding, deburring, brushing, polishing, satin
finishing, and matting of metal, wood, plastics, and such
like, including stone without the use of water. It is specifi-
cally ideal for plant construction and use in a robot cell.
The partly completed machinery may only be used in a
non-explosive environment where there are no flammable
liquids, gases or dusts!
1.3 i
ncOrrect use
All uses other than those described under section
1.2 are regarded as incorrect use and are there-
fore not admissible.
1.4 d
eclArAtiOn OF incOrpOrAtiOn
Translations of the «Einbauerklärung (Original)».
The manufacturer SUHNER Schweiz AG of Industri-
estrasse 10, CH-5242 Lupfig, hereby declares for the
partly completed machinery (see reverse side for type and
serial no.) that the following fundamental requirements of
the Directive 2006/42/EC are applied and fulfilled in ac-
cordance with Annex I: 1.1.2, 1.1.3, 1.1.5, 1.2.1, 1.2.2, 1.3.7,
1.3.8.1, 1.5.1, 1.5.4, and 1.6.1. Technical documentation
was generated for the partly completed machinery in ac-
cordance with Annex VII of the Machinery Directive. Docu-
ment Agent: M. Maglione. Authorised sites are provided
with this technical documentation in paper or electronic
form on justified request. This partly completed machin-
ery may be put into operation only when the machine in
which the partly completed machinery has been installed
has been ascertained to fulfil the conditions under the
Machinery Directive. CH-Lupfig, 08/2023.
M. Maglione/Division manager
18
S
oTES oN aFETy
2. c
2.1 n
Otes On sAFety during cOmissiOning
Before all work on the partly completed
machinery, it must first be disconnected
from the power supply.
Only a qualified person familiar with the safety regulations
may start up the partly completed machinery.
Always conduct test runs without workpieces.
Check the sense of rotation before starting the partly
completed machinery.
The operator must make sure that the components are
integrated and operate safely in the machine.
Only a qualified person may connect the electrical power
supplies in accordance with the local regulations.
The local grounding regulations must be observed and
implemented, and this implementation inspected.
Do not start the partly completed machinery until the
spindle has come to a stop.
Use only suitable tools, and never modify tools for an ap-
plication they have not been designed for.
Check the tool before use.Do not use a defective tool.
After transport, all electrical and mechanical connections
must be examined for damage and loosening, and any
remedial measures taken.
2.2 A
ssemBly instructiOns
The partly completed machinery
must be mounted by two people
and is fastened at the bores provi-
ded in the housing. Screws of quality grad 8.8 must be
used.
Connect the cables only after the partly completed ma-
chinery has been completely installed.
The installation must be carried out so that an air supply
to the motor is ensured.
2.3 c
Onnecting the pOwer tO the pArtly cOm
pleted mAchinery
Before any work is carried out on the part-
ly completed machinery, it must be en-
sured that the system is not connected to
a power source.
ommISSIoNINg
-