Safety Advice - Wolf Garten SDE 2100 Gebrauchsanweisung

Safety advice

General notes
Before using, check the connection lead for any signs of dam-
age or ageing.
If the mains connection lead is damaged when using the ap-
pliance it may not be touched until the plug has been removed
from the mains.
Attention! Blades continue to run after the motor has been
switched off.
Pull the plug from the socket,
–
when you leave the appliance,
–
before removing a blockage,
–
before checking, cleaning or repairing the appliance,
–
when a foreign body has been found (check the appliance
for damage and repair if required),
–
when the appliance vibrates a lot (check the appliance im-
mediately).
Preparatory measures
Never allow children to use the appliance.
Never use the appliance when people are in the vicinity.
Wear hearing protection and protective glasses. Wear these
throughout the entire operating duration of the appliance.
Do not wear loose or hanging clothes or clothes with hanging
straps or cords.
Only use the appliance outdoors (i.e. not near a wall or any
other rigid object) on a firm, even surface.
Do not use the appliance on a plastered surface scattered with
gravel.
Before commissioning the appliance, check the firm seating of
all screws, nuts and bolts, as well as other fixing material and
check that the covers and protective signs are in place.
Replace damaged or illegible stickers.
Cable
1
Attention! Electric shock through cable damage
When the cable is cut through or damaged, the safety fuse
does not always trip.
Do not touch cable before pulling out the power plug out
of the socket.
A damaged cable must be completely replaced. Repair-
ing the cable with insulating tape is not permitted.
Repairs to the cable should be performed only by an expert.
Do not scrape against corners, spikes or sharp objects.
Do not squeeze the cable between door jams or through win-
dows.
Switchgears must not be removed or bridged.
Use only extension cable not lighter than rubber hose,
type HO 7 RNF, minimum cross section 3 x 1.5 mm
max. 25 m.
Cables have to be protected against splashing water.
Handling
Ensure before starting the appliance that the feed hopper is
empty.
Keep your head and body away from the feed opening.
Do not place hands, other parts of the body and clothes in the
feed hopper, discharge channel or near moving parts.
10
Always ensure that you are balanced and on firm footing.
Do not stretch forward. Never place yourself higher than the
appliance when feeding in material.
When commissioning the appliance always stand outside the
discharge area.
When feeding in material ensure in particular that no metal,
stones, bottles, cans or other foreign bodies are included.
If foreign bodies should enter the cutting tool or should the ap-
pliance make unusual noises, switch the motor off immediate-
ly and allow the appliance to stop gradually. Remove the
mains plug and carry out the following procedures:
–
Check the appliance for damage
–
Check that the parts are firmly seated and tighten if required
–
Repair or replace any damaged parts (only use original
WOLF spare parts).
Do not allow processed material to accumulate within the dis-
charge area. This could compromise correct discharge and
lead to the kickback of material through the feed opening.
If the appliance is blocked, switch the motor off and remove
the mains plug before starting to clean.
Ensure that the motor is free from waste and other accumula-
tions to protect the motor from damage or overheating.
Ensure that all covers and baffles are in place and in correct
working order.
Do not transport the appliance when the motor is running.
Switch the motor off as soon as you leave the workstation and
remove the mains plug.
Do not tilt the appliance when the motor is running.
Maintenance and storage
If the appliance is to be switched off for maintenance, storage
or accessory replacement purposes, ensure that the energy
source is switched off and that the mains plug is removed. En-
sure that the moving parts are at a standstill. Allow the appli-
ance to cool before maintenance, adjustment etc.
When servicing the cutting tool, ensure that it can still always
run on, even when the motor is switched off.
Disposal
2
, length:
Power tools do not belong in household garbage.
Bring the device, accessories and packaging to an
environmentally-friendly recycling location.
G