Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Caution
• Turn on the monitor first before turning on the computer or
playback device.
• When switching the main power switch or the POWER
button off and back on, always wait for at least 5 seconds.
A short interval may result in a malfunction.
Turning on the main power
PN-LA652
Main power switch
Off mode, when main power is off.
Caution
• The main power must be turned on/off with the main power
switch. Do not connect/disconnect the power cord or turn
the breaker on/off while the main power switch is on.
• For a complete electrical disconnection, pull out the main
plug.
Turning power on
1. Press the POWER button or MONITOR ON button to
turn the power ON.
Status
Orange/Blue flashing
Blue lit
Orange lit
Blue flashing
*1 Standby mode when "POWER SAVE MODE" is set to "ON" and
"LAN PORT" and "MOTION SENSOR" is set to "OFF".
Networked standby mode when "POWER SAVE MODE" and "LAN
PORT" is set to "ON" and "MOTION SENSOR" is set to "OFF".
Networked standby mode allows the monitor to be turned on via
network (LAN, RS-232C, and HDMI CEC).
*2 When "POWER SAVE MODE" is set to "OFF" and "POWER
MANAGEMENT" is set to "ON", switching to input signal waiting
state when no signal is detected.
8
E
Turning Power On/Off
Main power switch
POWER button /Power LED
Status of the monitor
During power up
Power on
1
Power off (Standby state*
)
2
Input signal waiting state*
TIPS
• When the main power switch is off, the monitor cannot be
turned on.
• When the monitor is in the input signal waiting state and
press the POWER button or MONITOR ON button, the
monitor is turned on.
• When the monitor is in the input signal waiting state and
press the MONITOR OFF button, the monitor is turned off.
• To disable the logo screen from displaying when turning the
power ON, set "LOGO SCREEN" in "SYSTEM" to "OFF" on
the ADMIN menu. (See OPERATION MANUAL.)
• You can fix the input mode that appears after startup. Set
"START INPUT MODE" in "INPUT" on the ADMIN menu.
• When starting the option board, change "INPUT MODE" to
"OPTION."
• When you use the option board for the first time, the the
option board setup is executed. Do not turn off the main
power switch while the setup is running.
n O perations after first power-on
When you turn on the power for the first time, a setting screen
for language, communication, date and time, etc. appears.
Use the ▲, ▼, ,
buttons on the remote control to set.
The "LANGUAGE" screen appears.
1. After setting "LANGUAGE", select "NEXT" and press
the ENTER button on the remote control.
The "COMMUNICATION SETTING" screen appears.
2. After setting "COMMUNICATION SETTING", select "NEXT"
and press the ENTER button on the remote control.
The "DATE/TIME SETTING" screen appears.
3. After setting "DATE/TIME SETTING", select "NEXT"
and press the ENTER button on the remote control.
The "CONTROL FUNCTION" screen appears.
4. After setting "CONTROL FUNCTION", select "NEXT"
and press the ENTER button on the remote control.
The "VC ROOM SETTING" screen appears.
5. After setting "VC ROOM SETTING", select "FINISH"
and press the ENTER button on the remote control.
The settings below are recommended setting and conforms
to the "Normal Configuration" as defined in the EcoDesign
Regulation (2019/2021).
• POWER SAVE MODE: ON
• LAN PORT: OFF
• MOTION SENSOR: OFF
Turning power off
When you use the option board, look at the Operation Manual.
1. Press the POWER button or MONITOR OFF button.
The power is turned off. (Standby state)
POWER button /Power LED
Werbung
