SSS Siedle BVE 650-0 Produktinformation Seite 6

English
Montage
Application
The bus video receiver BVE 650-... is
used for the conversion of video and
control signals and for the power
supply from the 2-wire bus to the
monitor.
The BVE 650-... is mounted in a row
on the left hand side of the monitor
MOM/MOC/MOCT 711-...
In general, the BVE 650-... is
supplied as a wall surface-mounted
unit but with the ZMF 611-10
accessory can also be used as a
table-top unit and with the flush
mount frame accessory ZUR ... as a
flush-mounted unit.
The installation is routed via the bus
video receiver. For this reason, when
installing as a surface-mounted unit,
a flush junction box should be
positioned behind the bus video
receiver. The bus video receiver is
suitable for monochrome and colour
video transmission.
Installation
When using several BVE bus video
receivers, these must be connected
using a spur line via bus video distri-
butor unsymmetric BVVU 650-...
Note
The looping through from BVE to
BVE is not allowed.
Mounting the combination
BTS/BTC 750-... and MOM/MOC/
MOCT 711-...
1 Open the units.
2 (no illustration)
Disconnect the light current
connector and 2-pin flat connector
at the video cable, and separate
from the base plate of the
MOM/MOC/MOCT 711-... .
3 Break out the prepared connecting
webs "a" in the unit bases and screw
the bases together using the
connecting elements supplied with
the bus video receiver and the
monitor.
4 Fasten the units on the wall.
Connect in accordance with the
relevant wiring diagram.
5a Apartment station wiring.
5b Apartment station wiring.
In conjunction with MOCT 711-...
the supply must be provided via a
dedicated VNG 602-...
5c Apartment station wiring.
In conjunction with ZVM 711-02 or
when switching 2 MOM-/
MOC 711-... units in parallel, the
supply must be provided by a
dedicated VNG 602-...
6 (no illustration)
Plug in the following connecting
cables provided with the BVE:
a Connect the 4-core connecting
cable at the BTS/BTC 750-... at
terminals "Ta, Tb" as well as "15"
and "16", and on the circuit board
of the BVE at the HT connector (JP1).
b Plug the ribbon cable at the BVE in
the MOM/MOC connector (JP3) and
at the monitor MOM/MOC/
MOCT 711-...in the base plate on
the left at "VBE".
c Plug the video cable at the BVE in
the video connector "(JP2)" and at
the monitor MOM/MOC/
MOCT 711-... in the base plate at
the Video connector "(JP19)".
7 Plug the light current connector
on the base plate of the MOM/MOC/
MOCT 711-... and close the housing
components again.
8 (no illustration)
Terminal assignment:
TaM/TbM bus wires
+M/-M External supply voltage
20-30 V DC
External voltage supply if using
"Video memory accessory"
ZVM 711-..., MOCT 711-... or
parallel connection of Monitors
Monitor and ZVM 711-... is supplied
via a separate line rectifier e.g.
VNG 602-...
Voltage input must take place at the
relevant BVE 650-... at terminals
"+M" and "-M", not at MOM/
MOC/MOCT 711-...!
Specifications
• Cores at the input interchangeable
• External supply polarisation
protected
• Temperature range -0 to + 40° C
• Protection class IP 20
• Dimensions 62 x 230 x 35 mm
3