Bosch GDX Professional 180-LI Originalbetriebsanleitung Seite 14

OBJ_BUCH-3494-001.book Page 14 Friday, January 12, 2018 1:41 PM
14 | English
10 Universal bit holder*
11 Screwdriver bit*
12 Application tool (e. g. an impact socket)*
13 Carbon brushes
Technical Data
Cordless Impact Screwdriver
Article number
Rated voltage
No-load speed
Impact rate
Maximum torque, hard screwdriving
application according to ISO 5393
– ¼" hexagon socket
–  ½"
Bolt size
Tool holder
Weight according to EPTA-Procedure
01:2014
Permitted ambient temperature
– during charging
**
– during operation and during stor-
age
Recommended batteries
Recommended chargers
*depending on the battery pack being used
** limited performance at temperatures <0 °C
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-2.
Typically the A-weighted noise levels of the product are:
Sound pressure level 95,5 dB(A); Sound power level
106,5 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-2:
Impact tightening of fasteners of the maximum capacity of the
2 2
tool: a =9,5 m/s , K=1,5 m/s .
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745-2-2 and may be used to compare one tool with an-
other. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
1 609 92A 4AP | (12.1.18)
14 Cover lid
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
GDR 180-LI
3 601 JG5 1..
V=
-1
min 0 –2800
-1
min 0 –3600
Nm
Nm
mm M6 – M14
¼" hexagon socket
kg
°C
0...+45
°C -20...+50
GBA 18V..
GAL 18..
GAX 18..
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
Battery Charging
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
GDX 180-LI
3 601 JG5 2..
18
0 –2800
0 –3600
160*
–
M6 – M16
¼" hexagon socket
1.7*
0...+45
-20...+50
GBA 18V..
GAL 18..
GAX 18..
Bosch Power Tools
18
160*
180
 ½"
1.8*