Bosch GWS Professional 8-125 Originalbetriebsanleitung Seite 20

OBJ_BUCH-340-005.book Page 21 Friday, May 13, 2011 8:08 AM
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are
Sound pressure level
Sound power level
Uncertainty K=
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K determined according to
h
EN 60745:
Surface grinding:
a
h
K
Disk sanding:
a
h
K
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2004/108/EC,
2006/42/EC.
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Head of Product
Engineering Certification
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
31.03.2011
Bosch Power Tools
3 601 ... H20 ...
dB(A)
dB(A)
dB(A)
2
m/s
2
m/s
2
m/s
2
m/s
Assembly
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales
service agent for maintenance (for addresses, see section
„After-sales Service and Customer Assistance".
Protection Guard for Grinding
Place the protection guard 12 on-
to the spindle collar as shown in
the illustration. The triangle marks
on the protection guard must cor-
respond with the respective
marks on the gear case.
Press the protection guard 12 on-
to the spindle collar until the
shoulder of the protection guard
is seated against the flange of the
machine, and turn the protection
guard until it can clearly be heard
to engage.
Adjust the position of the protection guard 12 to the require-
ments of the work process. For this, press the release lever 1
upward and turn the protection guard 12 to the required po-
sition.
Adjust the protection guard 12 in such a manner that
sparking is prevented in the direction of the operator.
The protection guard 12 may be turned only upon actu-
ation of the release lever 1! Otherwise the power tool
may not continue to be used under any circumstances
and must be taken to an after-sales service agent.
English | 21
H22 ... H29 ...
H27 ... H23 ...
H21 ... H24 ...
H25 ...
H26 ...
91 91 91
102 102 102
3 3 3
5.5 8.5 7.0
2.0 2.0 2.0
3.0 3.0 3.0
1.5 1.5 1.5
1 619 929 J35 | (13.5.11)