Bosch UniversalDrill 18V-60 Originalbetriebsanleitung Seite 18

18 | English
Mechanical Gear Selection
You can press the gear selector switch (5) with the
u
power tool off or on. You should not do this at full load
or maximum torque, however.
Gear I:
Low speed range; for working with a large drilling diameter
or for screwdriving.
Gear II:
High speed range; for working with a small drilling diameter.
Setting the operating mode
UniversalDrill 18V-60:
Screwdriving
Set the torque presetting ring (3) to the re-
quired torque.
Drilling
Set the torque presetting ring (3) to the
"drilling" symbol.
UniversalImpact 18V-60:
Screwdriving
Set the operating mode presetting ring (4) to
the "screwdriving" symbol.
Set the torque presetting ring (3) to the re-
quired torque.
Drilling
Set the operating mode presetting ring (4) to
the "drilling" symbol.
Impact drilling
Set the operating mode presetting ring (4) to
the "impact drilling" symbol.
Fully automatic spindle lock (Auto-Lock)
The drill spindle, and therefore the tool holder (1), are
locked when the on/off switch (11) is not pressed.
This enables screws to be screwed in even when the battery
(7) is empty and allows the power tool to be used as a
screwdriver.
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the permitted bat-
tery temperature is exceeded, the electronics of the power
tool will switch off until the temperature returns to within the
optimum operating temperature range.
Practical advice
Only apply the power tool to the screw/nut when the
u
tool is switched off. Rotating tool inserts can slip off.
After working at a low speed for an extended period, you
should operate the power tool at the maximum speed for ap-
proximately three minutes without load to cool it down.
1 609 92A 7WM | (03.06.2022)
Maintenance and Service
Maintenance and Cleaning
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The recommended lithium-ion batteries are subject to legis-
lation on the transport of dangerous goods. The user can
transport the batteries by road without further require-
ments.
When shipping by third parties (e.g.: by air transport or for-
warding agency), special requirements on packaging and la-
belling must be observed. For preparation of the item being
shipped, consulting an expert for hazardous material is re-
quired.
Dispatch battery packs only when the housing is undam-
aged. Tape or mask off open contacts and pack up the bat-
tery in such a manner that it cannot move around in the
packaging. Please also observe the possibility of more de-
tailed national regulations.
Bosch Power Tools