Omnitronic OD 4T Bedienungsanleitung

USER MANUAL
EN
Thank you for purchasing this speaker for wall mounting. The speaker is specially
designed for application in PA systems operating with 100 V technology. The
speaker is protected against dust and low-pressure water jets and thus can be
used in outdoor areas. The connection must be made by skilled personnel only.
Please read these operating instructions carefully before using the product. They
contain important information for the correct use of your product. Please keep
them for future reference.
SAFETY INSTRUCTIONS
Only use the product according to the instructions given herein. No guarantee
Ÿ
claims for the units and no liability for any resulting personal damage or
material damage will be accepted if the product is used for other purposes than
originally intended, if it is not correctly connected or operated, or if it is not
repaired in an expert way.
Unauthorized rebuilds or modifications of the product are not permitted for
Ÿ
reasons of safety and render the warranty invalid.
This product is not a toy. Keep it out of the reach of children. Do not leave
Ÿ
packaging material lying around carelessly.
This product is in accordance with protection grade IP65 and can be used in
Ÿ
outdoor areas. However, do not immerse the product in water, this will destroy
it.
Protect the product against excessive humidity and heat. The recommended
Ÿ
temperature is -5 to +45°C.
Speaker cables are sensitive to electrical interference. Hence, it is
Ÿ
recommended to lay them at a distance of several meters to sources of
interference (e.g. dimmers, light switches).
Make sure that the product is installed securely and cannot fall down. Serious
Ÿ
injury to persons can be caused if the speakers fall down. Comply with the
standards and rules that apply in your country.
For commercial use the country-specific accident prevention regulations of the
Ÿ
government safety organization for electrical facilities must be complied with at
all times.
Make sure that impedance and power rating specified in the technical data
Ÿ
match the connected amplifier's data. Otherwise, the speakers or the amplifier
may be damaged. The total impedance for the connected speakers must not be
less than the minimum impedance for the amplifier.
This product is maintenance-free, except for occasional cleaning. You can use
Ÿ
a slightly dampened cloth for cleaning.
Never open the product. If this product is no longer working properly or is
Ÿ
visibly damaged, take it out of operation and consult your local dealer. Do not
attempt to repair the product yourself.
PROTECTING THE ENVIRONMENT
When to be definitively put out of operation, take the product to a local
recycling plant for a disposal which is not harmful to the environment.
Devices marked with this symbol must not be disposed of as household
waste. Contact your retailer or local authorities for more information.
© 2023 Omnitronic. All rights reserved • Omnitronic is a brand of Steinigke Showtechnic GmbH • Andreas-Bauer-Str. 5 • 97297 Waldbüttelbrunn, Germany
OD 4/5/6/8T
During operation, there is a hazard of contact with a voltage of up to 100 V at the
connection wires. The installation must be carried out by skilled personnel only.
Always insulate the connection cables which are not used. Observe the load of
the PA amplifier by the speakers. An overload may damage the amplifier! The total
power of all speakers connected must not exceed the amplifier power.
Mount the speaker to the wall using the supplied bracket.
Ÿ
If the PA system is turned on, turn it off before making any connection.
Ÿ
Remove the cover from the speaker.
Ÿ
Connect the speaker to the amplifier outputs with a suitable speaker cable
Ÿ
(black clamp = negative pole, red clamp = positive pole).
When connecting several speakers, make sure that all speakers have the same
Ÿ
polarity and that the amplifier is not overloaded.
Adjust the rotary switch to the desired power rating for the 100 V operation or
Ÿ
select the 8 Ω position, for directly operating the speaker at a low-impedance
amplifier output.
Replace the cover.
Ÿ
TECHNICAL SPECIFICATIONS
Subject to change.
Publ. 07/2023