Seite 1
Metal Garden Shed OWNER'S MANUAL Instructions for Assembly GERÄTEschRank MIT flachDach aufbauanlEITunG SPR10009 Requires two people and takes 1-1.5 hours for lnstallation. Quick & Easy Assembly Ridge Reinforced Walls Available in Various Sizes Lesen Sie die Aufbauanleitung sorgfältig, bevor Sie mit dem Aufbau des Geräteschrankes beginnen.
Seite 2
BEFORE YOU START Owner's Manual Prior to installation, it is important that you contact your local government authority to determine if building approval is required. Study and understand this owner's manual. Important information and helpful tips will make your construction easier and more enjoyable.
Seite 3
PLAN AHEAD Site Selection Avoid overhanging trees as much as possible as leaves will make regular cleaning necessary and broken branches are a potential hazard. Small trees,bushes or fences nearby can be helpful,acting as a wind break. Site Preparation The site must be prepared so that the base of the shed is level all round and checking with a spirit level is required.
Seite 4
allGEMEInE InfoRMaTIonEn Bevor Sie mit der Montage beginnen, stellen Sie sicher, dass die für Sie zutreffenden Richtlinien/Gesetze eingehalten werden. Planen Sie für die Montage mindestens 390 bis 450 Minuten Zeit ein. Für die Montage werden mindestens 2 Personen benötigt. Prüfen Sie vor dem Beginn der Arbeit, dass alle Teile in der richtigen Menge vorhanden sind.
Seite 5
wERkzEuGE unD ausRüsTunG Sicherheitskleidung (Sicherheitsschuhe, Schutzhandschuhe, Schutzbrille, Helm etc.) Wasserwaage Längenmesser Standleiter (ca. 1,5 m Höhe) Schrauben- oder Ratschen-Schlüssel Akkuschrauben und Bohrmaschine mit ver. Aufsätzen Schraubendreher (nicht im Lieferumfang enthalten) VERPackunGsEnTsoRGunG Entsorgen Sie die Verpackung sortenrein. Pappe und Karton wird als Altpapier entsorgt und Folien führen Sie der entsprechenden Wertstoffsammlung zu.
Seite 6
TEIlE-lIsTE PART LIST / QTY/ QTY/ TEIl TEIl PART/ PART/ NO./ NO./ MEnGE MEnGE 1683mm 752mm 1683mm 1169mm 811mm 1169mm 811mm 473mm 1140mm 473mm 1140mm 1479mm 1159mm 1120mm 1159mm 1120mm 803mm 1700mm 803mm 1700mm 803mm 1682mm 803mm 29-1 1600mm 348mm 348mm 1700mm 1700mm...
Seite 8
QTY/ QTY/ TEIl TEIl PART/ PART/ NO./ NO./ MEnGE MEnGE QTY/ TEIl PART/ NO./ MEnGE QTY/ TEIl PART/ NO./ MEnGE...
Seite 9
、 Wen diagonal measurements are equal,the frame is square. 、 The Floor Frame must be BOTH square AND level or the holes will not line up properly. achten sie darauf, dass die beiden Diagonalen des Rahmens gleich lang sind und sich der boden in der waage befindet, ansonsten liegen die löcher nicht richtig übereinander.
Seite 10
QTY/ TEIl PART/ NO./ MEnGE QTY/ TEIl PART/ NO./ MEnGE QTY/ TEIl PART/ NO./ MEnGE...
Seite 11
QTY/ TEIl PART/ NO./ MEnGE 10L&10R QTY/ TEIl PART/ NO./ MEnGE QTY/ TEIl PART/ NO./ MEnGE...
Seite 12
QTY/ TEIl PART/ NO./ MEnGE QTY/ TEIl PART/ NO./ MEnGE QTY/ TEIl PART/ NO./ MEnGE...
Seite 13
QTY/ TEIl PART/ NO./ MEnGE QTY/ TEIl PART/ NO./ MEnGE QTY/ TEIl PART/ NO./ MEnGE...
Seite 14
QTY/ TEIl PART/ NO./ MEnGE QTY/ TEIl PART/ NO./ MEnGE...