Werbung
Verfügbare Sprachen
Verfügbare Sprachen
15239 Bass trumpet/
Flugelhorn stand
INTENDED USE
- High-quality, stable stand for bass trumpet/bass flugelhorn
FEATURES & CAPABILITIES
- Very solid and durable steel construction
- Wobble-free stand
- Unsurpassed ease of handling without the use of tools
- Suitable for rehearsal room, studio and stage as well as for mobile use;
-
the compact package is also well-suited for transport and storage
- The variably adjustable receptacle cone is completely encased in
-
high-quality plastic;its rubber-like properties protect the instrument
-
from scratches
- Adjustable height 480 - 700 mm, footprint: diameter 570 mm, weight 1.06 kg
Thank you for choosing this product. Please read and follow these instructions carefully. They
provide information on all of the important steps necessary to set up and operate your product
safely. We recommend that you also keep them for future use.
SAFETY INSTRUCTIONS
- Always carry out a visual inspection before use;
-
damaged components must not be used any further.
- Ensure a suitable and level surface.
- Because the moving parts, pinching hazards may naturally occur;
-
careful handling during assembly, operation and dismantling is
-
therefore indispensable.
- Place the instrument carefully in the stand.
- We recommend removing the instrument from the stand
-
before adjusting the height.
- The parquet protectors are made of high-quality material and as
-
far as technically possible, free of plasticizers; to protect highly
-
sensitive floors (possibly certain types of parquet), a non-slip
-
carpet pad should be used if necessary.
INSTALLATION INSTRUCTIONS
1. COMPONENTS
Please carry out a visual check that all parts are present
and in order - as far as recognisable
a BASE:
a
a.1 Folding foot (3x)
a
a.2 Base clamping screw M6 x 22 mm
b TUBE COMBINATION:
b
b.1 Base tube diameter 20 mm
b
b.2 Clamp–clamping screw M6 x 12 mm
b
b.3 Extension tube diameter 16 mm
c INSTRUMENT SUPPORT:
c
c.1 Support clamping screw M6 x 12 mm
c
c.2 Support, rubberized
c
c.3 End cap
2. SET UP THE STAND
The stand is already completely pre-assembled.
It simply needs to be put in the correct position.
2.1 Slightly loosen the clamping screw b.2 of the clamp
2.2 Extend extension tube b.3
2.3 Re-tighten the clamping screw b.2
2.4 Unfold foot tubes a.1
2.5 Loosen the base clamping screw b.2 and...
2.6 ...push the base downwards as far as the stop
2.7 Tighten the base clamping screw b.2 again
3. SET INSTRUMENT ON STAND
3.
- PROCEDURE -
The aim is to place the bell of the instrument in
such a way that it rests without play both:
- on the top of the end cap c.3
- on the rubberized support at the bottom c.2
The double support ensures that the instrument
is permanently stored safely and gently.
The careful positioning of the supports according
to the dimensions of your instrument is a prerequisite
for this.
3.1 Loosen the support clamping screw c.1 and...
3.2 ...place support c.2 below.
3.3 Gently place the bell of the instrument, coming from
3.3
above, on the support cap of the extension tube.
3.4 Now gently push the support c.2 upwards until the
3.4
rubber cone is in contact with the bell.
3.5 Secure this position by tightening the support
3.5
clamping screw c.1.
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
15239-000-55 Rev.01 03-80-962-00 8/23
1. COMPONENTS
2. SET UP
2.
THE STAND
3. SET INSTRUMENT ON STAND
3.
- PROCEDURE -
Werbung
