Bosch GBH 18V-36 C Professional Originalbetriebsanleitung Seite 321

Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Control Via App
The cordless worklight is fitted with a Bluetooth® module
which enables wireless data transfer to certain mobile
devices with a Bluetooth® interface (e.g. smartphone, tab-
let).
In order to control the cordless worklight via Bluetooth®, you
will need the "Bosch Toolbox" app. Download the app from
the corresponding app store (Apple App Store, Google Play
Store).
Then select the "My Tools" subitem in the app. The display of
your mobile device will show you all subsequent steps re-
quired to connect the cordless worklight to the device.
The following functions will be available when a connection
has been established with the mobile device:
– Remote control
– Time control
– Grouping several cordless worklights
– Personalisation
– Status check, output of warning messages
– General information and settings
– Management
Practical Advice
Shortly before the cordless worklight switches off because
of an empty battery, it will flash three times and shine with
reduced brightness.
The cordless worklight will flash five times just before it is
about to switch off due to the time control.
You can adjust the time control via the app(see "Control Via
App", page 13).
Bosch Power Tools
Errors – causes and corrective measures
Cause
A Bluetooth® connection cannot be established with the
cordless worklight.
Capacity
The cordless worklight is not
60−100 %
emitting a Bluetooth® signal.
30−60 %
5−30 %
The cordless worklight cannot be operated via
Bluetooth® even though the battery is inserted and
0−5 %
charged.
The Bluetooth® module is not
activated.
The cordless worklight cannot be switched on after
Capacity
wireless charging.
80−100 %
The inductively chargeable
60−80 %
battery has to be re-initial-
40−60 %
ised.
20−40 %
The PIN for the Bluetooth connection is not working.
5−20 %
The PIN must be reset to
0−5 %
factory settings.
Maintenance and Service
Maintenance and Cleaning
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
The cordless worklight is maintenance-free and does not
contain any parts that need to be replaced or maintained.
Only clean the cordless worklight's plastic lens with a dry,
soft cloth to prevent damage. Do not use any detergents or
solvents.
If the button cell has fully discharged, replace it with a new
one.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
English | 13
Corrective measures
Remove the button cell (11)
and battery (14) for 10
seconds.
Press the on/off switch (1)
repeatedly until the cordless
worklight can be operated
via Bluetooth®.
Remove the battery (14) for
10 seconds.
Remove the button cell (11)
and battery (14) for 10
seconds.
1 609 92A 634 | (11.11.2020)