Bosch GSA 185-LI Professional Originalbetriebsanleitung Seite 15

Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out. Do not use force to do
this.
The rechargeable battery has two locking levels to prevent
the battery from falling out if the battery release button is
pressed unintentionally. The rechargeable battery is held in
place by a spring when fitted in the power tool.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LED
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LED
5 × continuous green light
4 × continuous green light
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Bosch Power Tools
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Inserting/changing the saw blade
When fitting or changing the saw blade, wear protect-
u
ive gloves. Blades are sharp and can become hot when
used for prolonged periods of time.
While replacing the saw blade, ensure that the saw
u
blade receptacle is free of material residue, e.g. wood
or metal chips.
to
Selecting the saw blade
Only use saw blades with a 1/2" universal shank. The saw
blade should not be longer than required for the intended
cut.
Inserting the saw blade (see figure A)
Firmly push the saw blade (1) into the saw blade
receptacle (4) until it audibly engages. The locking
sleeve (3) consequently rotates by approx. 90° and locks
the saw blade in place.
Capacity
If the saw blade (1) is not locked, rotate the locking
60–100 %
sleeve (3) by approx. 90° in the direction of the arrow until it
is locked in the open position and a clicking sound is heard.
30–60 %
Then push the saw blade into the saw blade receptacle (4)
5–30 %
once again.
0–5 %
Check that it is seated securely by pulling the saw
u
blade. A loose saw blade can fall out and lead to injuries.
For particular jobs, the saw blade (1) can also be flipped
180° (teeth point upwards) and refitted.
Ejecting the saw blade (see figure B)
When ejecting the saw blade, hold the power tool in
u
Capacity
such a manner that no persons or animals can be in-
80–100 %
jured by the ejected saw blade.
60–80 %
Turn the locking sleeve (3) by approx. 90° in the direction of
40–60 % the arrow. The saw blade (1) is ejected.
20–40 %
Dust/Chip Extraction
5–20 %
Dust from materials such as lead-containing coatings, some
0–5 %
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
English | 15
1 609 92A 7FC | (06.04.2022)