Assembly; Clothing; Operating The Tiller; Operation Zone - Texas A/S Lilli 534B Bedienungsanleitung

Maintenance and storage
The engine shall be stopped when carrying out
maintenance and cleaning operations, when changing
tools and when being transported by means other than
under its own power.
Check regularly that all bolts and nuts are tightened.
Retighten if necessary.
The engine must be completely cooled before storing
indoors or covered.
If the machine unused for a period of time, please refer
to the instructions in this manual.
Maintain or replace safety and instruction labels, as
necessary.
Only use original spare parts or accessories. If not
original parts or accessories is used, the liability is no
longer applied.
Replace faulty silencers.
Miscellaneous
The gears are delivered pre-greased. However, always
ensure they are well greased before each use.
The motor is not pre-filled with oil.
Factory-fitted control devices, such as the handle-
mounted clutch cable, must not be removed or exposed.
Only drain the fuel tank outdoors. Gasoline is extremely
flammable, and the fumes are explosive.
Ensure that the machine is properly secured when
transported on a flatbed etc.
Reduce the throttle during engine shutdown and close
the fuel valve.
Due to vibrations, it is recommended to take a break for
every 30 minuttes use to avoid fatique in your arms.

Assembly

Please follow the steps in figure:
(Actual model may vary from the illustration shown)
1. Box content
A. Extension blades
B. Tiller with cables and support wheels
C. Blades Outer
D. Side guards
E. Handlebar (Lilli 572/575)
F. Depth skid
G. Mounting bracket for handlebar (Lilli 572/575)
H. Lower handle x2 (Lilli 534/535)
I. Handlebar (Lilli 534/535)
2. Only for model Lilli 534/535:
Fit the lower handle section. Use the supplied mountings
and bolts.
Fit the handle. Use the supplied assembly kit as shown.
3. Only for model Lilli 572/575:
Fit the handle into the bracket (1-G) fasten with hand
wheel.
NB: Ensure the bolt goes through the spring.
4. Mount clutch handle and throttle control as shown on the
picture.
5. Mount the side guards using the bolts and nuts supplied.
Note the side guard must go under the body frame.
6. Mount the blades using the cotter bolts and pins.
7. Mount the depth skid with the cotter bolt and pin.
8. Fit the panel to the handlebar with the 4 screws.
(only Lilli 572/575)
Fill the engine with oil.
See changing the oil section for more details.

Clothing

When using the machine, wear close-fitting work clothes,
hard-wearing work gloves, ear defenders and non-slip boots
with steel toecaps.

Operating the tiller

Ensure the machine is placed on a level surface with the
support wheels lowered prior to start.
Remove all foreign objects from the work area before
using the machine. Stones, glass, branches and similar
items may damage the tiller. Also, check the bolts on the
tiller are tightened.
Start the motor as per the instructions below. Stand
clear of the machine's moving parts.
Never attempt to move the machine in any way other
than intended for normal use while the motor is running.
The tiller is designed for use in vegetable gardens and
flowerbeds. Ensure that you are familiar with these
instructions before operating the machine, in particular the
motor start and stop procedures.
Fig 9: To use the black handle the control stick must first be
activated. By tilting the control stick to the right or left side
and then activate the black handle lever, the tiller will move
forward or backwards.
Pay attention while reversing. It is important that the area is
cleared, for any obstacle before reversing. Never reverse the
tiller against a wall, tree or any other fixed obstacle.

Operation zone

While the machine is being operated and the motor is
running, do not leave the operation zone marked fig 11.
If it is necessary to leave the operation zone, for example to
attach an accessory, first stop the engine.
It is normally necessary to drive the tiller over a section of
earth 2-3 times from different directions. Do not till very wet
soil, as clods of earth will form that are difficult to break up.

Adjusting the handle

Lilli 572/575 only: Fig 13. The handle angle can be adjusted.
Use the two hand wheels to set one of the 3 available
positions. The handle can be flipped forward during
transport. NB: Ensure the cables do not become trapped.

Adjusting the wheel/ depth skid

Fig. 14: The support wheels are mounted on the tiller. They
can be adjusted to the required height by pulling the lock
handle (A) and moving the ring up or down. The wheel ring
can be used to stabilise the machine when tilling and help to
prevent the machine falling into soft soil.
Fig. 15. The depth skid can be adjusting for tilling in three
different depths.The deeper the depth skid sits in the soil, the
deeper the tilling blades will work and the slower the
machine will advance.The right cultivating depth will lighten
your workload.The correct tilling depth depends on the soil,
and we recommend you make several attempts to see how
deep the depth skid should be so that you can work optimally
in your soil.
To adjust the depth skid, pull it backwards and up till the
preferred height is found.Place the depth skid vertically, and
it will fall into a notch.
13