Optional Accessory - Makita UT001G Betriebsanleitung

For UT002G
1. Insert the shaft into the chuck as far as it will go.
► Fig.8: 1. Shaft 2. Chuck
2.
Tighten the chuck by hand, and then place the
chuck key in each of three holes and tighten it clock-
wise. Be sure to tighten the chuck key at all three holes
evenly.
► Fig.9: 1. Chuck key 2. Chuck
3. To remove the shaft, turn the chuck key coun-
terclockwise at one of the holes, and then loosen the
chuck by hand.
4. When not in use, store the chuck key as shown in
the figure to keep it from being lost.
► Fig.10: 1. Chuck key
Installing the mixing blade

Optional accessory

Insert the mixing blade into the shaft and secure it with
the hex bolt. At this time, position it so that the top end
of the hex bolt always fits to the flat surface on the shaft
and tighten the hex bolt with the provided wrench.
► Fig.11: 1. Hex bolt 2. Shaft 3. Flat surface 4. Mixing
blade
When installing the mixing blades at two different posi-
tions, mount and secure the two mixing blades on the
flat part of the shaft with the hex bolts so that the same
surface of the mixing blades faces each other as shown
in the figure.
► Fig.12: 1. Hex bolt 2. Shaft 3. Flat surface 4. Mixing
blade
NOTE: Ask your local Makita Service Center about
which is mixing blades are allowed.
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge firmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the tool and battery cartridge
and a personal injury.
CAUTION:
Do not use this tool with the
battery adapter. If you connect the battery adapter
to the tool, the battery cover cannot be closed, and
using the tool with battery cover opened may cause
an injury.
CAUTION:
Be careful not to pinch your fin-
gers when opening or closing the battery cover.
NOTICE:
Install a battery cover that matches the
size of the battery.
Open the battery cover while pressing the button on the
battery cover.
► Fig.13: 1. Button 2. Battery cover
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
► Fig.14: 1. Red indicator 2. Button 3. Battery
cartridge
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator as
shown in the figure, it is not locked completely.
After installing the battery cartridge, close the battery
cover securely.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
Switch action
WARNING:
Before installing the battery car-
tridge into the tool, always make sure that the
switch trigger actuates properly and returns to
the "OFF" position by fully pulling and releasing
it.
WARNING:
NEVER defeat the lock-off button
by taping down or some other means. A switch with
a negated lock-off button may result in unintentional
operation and serious personal injury.
WARNING:
NEVER use the tool if it runs when
you simply pull the switch trigger without press-
ing the lock-off button. A switch in need of repair
may result in unintentional operation and serious
personal injury. Return tool to a Makita service center
for proper repairs BEFORE further usage.
WARNING:
Do not install the battery cartridge
with the lock button engaged.
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
depress the lock-off button and pull the switch trigger.
Tool speed is increased by increasing pressure on the
switch trigger. Release the switch trigger to stop.
For continuous operation, depress the lock button while
pulling the switch trigger, and then release the switch
trigger. To stop the tool, pull the switch trigger fully, then
release it.
► Fig.15: 1. Switch trigger 2. Lock-off button 3. Lock
button
9 ENGLISH