Bauknecht B7I HF60 TUSC CH Bedienungsanleitung Seite 6

EN
PROBLEMS POSSIBLE CAUSES
No water in the water supply or the tap is closed. Make sure there is water in the water supply and the water tap is open.
The dishwasher does
not fill the water.
The water inlet hose is kinked.
The display shows:
H 2 O and is
lit; acoustic alarm
The screen in the water inlet hose is clogged; it is
sounds.
necessary to clean it.
The filter is clogged with food residues or lime-
scale.
The dishwasher
Drain hose positioned too low or siphoning into
finishes the cycle
the home sewage system.
prematurely.
The display shows:
F8 E3
An excessive amount of foam is present.
Air in the water supply.
Rinse aid is not present or the dosage is too low.
The dishes have been unloaded after the door
was opened automatically but before the actual
cycle end.
The dishes are not
dried well.
The dishes are sitting too flat.
The selected cycle does not have the drying
phase.
The dishes are made of non-stick or plastic.
Dishes and glasses
have blue streaks Rinse aid dosage is excessive.
or bluish tinges.
The salt reservoir is empty.
Dishes and glasses
The water hardness setting is too low.
are covered with li-
mescale or a whitish
The cap of the salt reservoir is not properly closed. Check and close the salt reservoir cap.
film.
The rinse aid reservoir is empty or the rinse aid
dosage is insufficient.
The dishwasher
Valve is blocked or faulty.
shows F8 E5
Policies, standard documentation, ordering of spare parts and additional product information can be
found by
:
• Using QR code and visiting our website: docs.bauknecht.eu
• Visiting our website: parts-selfservice.whirlpool.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting
our After-sales Service, please state the codes provided on your product's identification plate.
The model information can be retrieved using the QR-Code reported in the energy label. The label also includes
the model identifier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu
6
SOLUTIONS
Check the inlet hose (see INSTALLATION). Open dishwasher door, press START/Pause button and
close the door within 4 seconds.
Check and clean the screen in the water inlet hose. Open dishwasher door, press START/Pause
button and close the door within 4 seconds.
Clean the filter and descale the appliance (see CLEANING THE FILTER ASSEMBLY and DESCALE
INSTRUCTION).
Check if the end of the drain hose is placed at the correct height (see INSTALLATION). Check for
siphoning into the home sewage system, and install a siphon breaker/air admittance valve if
necessary.
The detergent has not been measured out correctly or it is not suitable for use in dishwashers
(see FILLING THE DETERGENT DISPENSER).
Check water supply for leaks or other issues letting air inside.
Make sure the rinse aid dispenser is filled (see FILLING THE RINSE AID DISPENSER). Multifunctional
tablets only will not provide as good drying effects as the actual use of liquid rinse aid.
Make sure the cycle has ended before starting to unload the dishes (see DAILY USE). For even
better drying results, it is recommended to let the dishes sit inside the dishwasher with the door
open for additional 15 minutes after the cycle ends.
If you notice puddles of water inside cavities of cups, mugs or bowls, try loading the dishes
(especially in the upper rack) providing more inclination to let larger amounts of water drip
down before drying starts.
Please check in the PROGRAMS TABLE if the selected program is equipped in the drying phase.
A cycle without the drying phase may not deliver desired drying efficiency, so it is recommended
to change cycle selection for the one that has the drying phase.
Some water drops remaining on this type of material are normal.
Adjust the dosage to a lower setting.
Refill the reservoir with salt as soon as possible. Using the appliance without salt may cause
damage to its internal components.
Increase the setting (see WATER HARDNESS TABLE).
Refill the dispenser with rinse aid and check the dosage setting (for more information - see
FILLING THE RINSE AID DISPENSER).
Close the water tap, if possible. Do not switch off the power supply. Call the service.
IEC 436
: