Electrical Characteristics; Battery Charge - CANGAROO MIA D-118 Gebrauchsanweisung

•Charger: AC: 100 – 240V; 50-60 Hz; DC: 5V/ 1A
•Battery capacity: 3.7V-2000 mAh
• Power rating: 5W
•Noise limit: ≤ 60dB(A)
•Motor protection: II
•Conditions for use: 5˚C ̴ 40˚C, 10% ~ 90% RH
•Charging time: 2 часа
•Method of control: touchscreen panel
•Display: LED
1.Before first time use charge the battery completely.
2.The breast pump is with a built-in battery 3.7V/ 2000 mAh.
3.Charging:
-Connect the adapter to the charging jack of the pumping mechanism.
-Insert the plug into electrical outlet of the mains supply of your home.
-We recommend you leave the breast pump to charge completely before next use in order to prolong its battery life.
4.Use only the charger provided with the breast pump. Do not use chargers from other products.
5.Charge the battery on time. Charge as soon as the battery indicator is with 1 bar or the indicator starts flashing.
6.After the battery is fully charged the indicator will stop flashing.
7.If you will not use the product for a long time, charge the battery completely before storing it. Then charge the battery
at least once a month to prolong its life.
8.If the battery is damaged or cannot be charged anymore, do not try to open the product by yourselves. For consultation
and repair contact the shop from where you bought the product or the importer/ distributor.
9.The battery is recyclable. If the product is damaged and cannot be used any longer, take it to an official collection point
for electronic products' waste, batteries, chargers. DO NOT throw the product away with the household waste. Follow
your country's rules for the separate collection of electrical and electronic products and rechargeable batteries. Dispose
of waste of this type only at the designated places. This will be important and significant contribution for the
environmental protection and the reduction of the harmful effects of the substances contained in batteries and electronic
components on the environment and human health.
ATTENTION! NEVER STERILIZE OR IMMEDIATE THE PUMP MECHANISM AND TUBE CONNECTING IT TO THE PUMP BODY.
Follow the instructions and sequence for assembling the product, described in the text and images hereafter attached.
1.Step 1: Insert the silicone massaging pad (2) into the horn mouth (3) and gently press them together to provide the
necessary seal. Put the dust shield (1).
2.Step 2: Attach the assembled part to the pump body (5), making sure it is well fixed.
3.Step 3: Insert the silicone cylinder (4) into the upper part of the pump body (5). Be careful not to tear or scratch the
cylinder because this will affect the pumping vacuum. Fit and tighten the pump cover (6) securely over the silicone
cylinder (4) so that it fits securely over the silicone cylinder.
4.Step 4: Place the valve at the lower end of the pump body. Make sure that it is properly fixed around the ends of the
pump body opening intended for it. Important! If the valve is loose or not installed correctly, it will not be possible to
create a sufficient vacuum !
5.Step 5: Fix the feeding bottle (10) to the pump body by turning the bottle gently clockwise so that the thread of the
bottle coincides exactly with the thread of the pump body
6.Step 6: Insert one side of the tube (7) towards the pump body (5). Then insert the other side of the tube (13) into the
pump motor. So you can now use the breast pump.
Using the pump - See Figure UD.
1. Wash your hands thoroughly and make sure your breasts are clean. Express some milk to check that your milk ducts are
not blocked. The pump must be sterile and assembled.
2. Sit down and relax in a comfortable chair, leaning forward slightly (Use a soft and comfortable pillow as a backrest).
3.Put the pump on your breast and start the pump motor.
III. ELECTRICAL CHARACTERISTICS
IV. BATTERY CHARGE
V. ASSEMBLY OF THE ELECTRIC BREAST PUMP
VI. USE
13