Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
2. To remove the battery pack, pull the battery
EN
off the compartment.
3. Return the battery compartment locker to the
original position.
Low battery indicator
1. Reduced power, distortion and a "stuttering
sound" or low battery sign (
appears on the display are all the signs that
the main battery pack needs to replace.
NOTE: The battery pack can't be charged
via the supplied AC power adaptor.
2. When the main battery is removed and the
low battery sign (
shown on the display, this indicates that it is
time to replace the back up batteries.
Using the soft bended antenna [Fig. 3]
Straight up the soft bended antenna.
CAUTION:
The soft bended antenna works in one
direction only.
Forcibly bending it can cause it to break or
result in an injury.
Using Supplied AC power adaptor
Remove the rubber cover and insert the
adaptor plug into the DC socket on the right
side of the radio. Plug the adaptor into a
standard mains socket outlet. Whenever the
adaptor is connected, the battery pack is
automatically disconnected. The AC adaptor
should be disconnected from the main
supply when not in use.
NOTE:
• The sound is slightly quieter when using an
AC power adaptor than when using a battery
pack.
• When the radio has any interference in
AM band by its adaptor, please move the
radio away from its AC adaptor over
30 cm.
• When the AC adaptor and the battery
pack are used simultaneously, the AC
adaptor will take precedence in powering
the unit. In this case, the power of the
battery pack will not be consumed.
• This unit does not have a charging
function. Running the unit using both the
AC adaptor and battery pack at the same
time will not charge the battery pack.
• The AC power adaptor is for exclusive
use with this product and is not to be used
with other equipment. Also, do not use
AC adaptor for other equipment with this
product.
EY37A2.indb 10
) that
) flashes and an "E." is
- 10 -
III. OPERATIONS
Operating the radio – Scan tuning
AM/FM
NOTE:
If the reception signal is weak, try
changing the orientation of the radio or
antenna.
1. Press and hold the Power button to switch
on the radio.
2. Press the Source button until "AM" or "FM" is
displayed.
3. Press the Tuning control knob to carry out an
auto-tune. The radio will scan up the AM/FM
band from the currently displayed frequency
and will stop scanning automatically when it
finds a station of sufficient strength.
4. After a few seconds the display will update.
The display will show the frequency of the
signal found.
5. To find other station, press the Tuning control
knob as before.
6. When the end of the waveband is reached
the radio will recommence tuning from the
opposite end of the waveband.
7. Rotate the Volume control to adjust the
sound level as required.
8. To switch off the radio, press and hold the
Power button .
Manual tuning – AM/FM
1. Press and hold the Power button to switch
on the radio.
2. Press the Source button until "AM" or "FM" is
displayed.
3. Rotate the Tuning control knob to tune to a
station.
4. When the end of the waveband is reached
the radio will recommence tuning from the
opposite end of the waveband.
5. Use the Volume control to adjust the sound
level as required.
Presetting stations in AM/FM mode
There are 6 preset stations each for AM and
FM radio. They are used in the same way for
each waveband.
1. Tune to the required radio station as
previously described.
2. Press and hold the required Preset button (1
to 6) until the radio beeps. "M1" for example
is shown next to the frequency. The station
will be stored using the preset number.
Repeat this procedure for the remaining
presets as needed. Preset stations which
have already been stored may be overwritten
by following the above procedure if required.
2015-2-13 9:53:16
Werbung
Inhaltsverzeichnis
