Prior To Operation - DeWalt DCS331N Bersetzt Von Den Originalanweisungen

EngLIsh
4. Release the keyless blade release lever.
To Remove a blade

CAUTION: Do not touch used blades, they may be hot.
Personal injury may result.
1. Lift the keyless blade release lever
2. With a slight shake the blade will drop out.
Beveling the Shoe (Fig. G)
To unlock the shoe, pull the keyless bevel lever
To lock the shoe, push the keyless bevel lever back under the
body of the jigsaw.
To Bevel the Shoe
1. Unlock the shoe.
2. Slide the shoe forward to release it from the 0° positive
7
stop position.
3. The shoe can be beveled to the left or to the right and
has detents at 15°, 30° and 45°. The shoe can be manually
stopped at any degree between 0° and 45°.
4. Once the desired bevel angle is achieved, lock the shoe
into place.
To Set Shoe Back to 0°
1. Unlock the shoe.
2. Rotate the shoe back to 0°.
3. Slide the shoe back into the 0° positive stop position.
4. Lock the shoe.
Cutting Action – Orbital or Straight (Fig. H)
This jig saw is equipped with four cutting actions, three orbital
and one straight. Orbital action has a more aggressive blade
motion and is designed for cutting in soft materials like wood
or plastic. Orbital action provides a faster cut, but with a less
smooth cut across the material. In orbital action, the blade
moves forward during the cutting stroke in addition to the up
and down motion.
nOTE: Metal or hardwoods should never be cut in orbital action.
To adjust the cutting action, move the orbital action lever
between the four cutting positions: 0, 1, 2, and 3. Position 0
8
is straight cutting. Positions 1, 2, and 3 are orbital cutting. The
aggressiveness of the cut increase as the lever is adjusted from
one to three, with three being the most aggressive cut.
Dust Blower (Fig. I)
The dust blower helps clear the cutting area of debris created
from the blade.
nOTE: When cutting metal, turn the dust blower off so cutting
fluids are not blown away from the blade.
To turn the dust blower on, slide the dust blower control
the way to the top.
To turn the dust blower off, slide the dust blower control all the
way to the bottom.
Removeable Anti-Scratch Shoe Cover (Fig. J)
The anti-scratch shoe cover 10
surfaces that scratch easily, such as laminate, veneer or paint.
36
5 .
to the side.
6
9 all
should be used when cutting
To attach anti-scratch shoe cover
aluminum shoe 7 into the front of the anti-scratch shoe cover
and lower the jig saw. The anti-scratch shoe cover will click
securely onto the rear of aluminum shoe.
To remove anti-scratch shoe cover, grasp the anti-scratch shoe
cover from the bottom; holding onto the two rear tabs
remove the anti-scratch shoe cover.
Anti-Splinter Insert (Fig. K)
nOTE: Do not use the anti-splinter insert with the flush
cutting blade.
The anti-splinter insert should be used when trying to
14
minimize tear-out, especially when cutting veneer, laminate, or
finished surfaces, such as paint. The anti-splinter insert should
be installed into the anti-scratch shoe cover
cover is not used, install anti-splinter insert into shoe

Prior to Operation

• Make sure your battery pack is (fully) charged.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, depress the trigger lock button and
disconnect battery pack before making any
adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.

WARNING: Always wear proper personal hearing
protection. Under some conditions and duration of use,
noise from this product may contribute to hearing loss.
Instructions for Use

WARNING:
• Always observe the safety instructions and applicable
regulations.
• Make sure your workpiece is well secured. Remove
nails, screws and other fasteners that may damage
the blade.
• Check that there is sufficient space for the blade
underneath the workpiece. Do not cut materials that
are thicker than the maximum cutting depth.
• Use sharp saw blades only. Damaged or bent saw
blades must be removed immediately.
• Never run your tool without a saw blade.
• For optimal results, move the tool smoothly and
constantly over the workpiece. Do not exert lateral
pressure on the saw blade. Keep the shoe flat on the
workpiece. When sawing curves, circles or other round
shapes, push the tool gently forward.
• Wait until the tool has come to a standstill before
removing the saw blade from the workpiece. After
sawing the blade may be very hot. Do not touch.
, place the front of the
10
13
10 . If the no-mar
.
7