Inhaltsverzeichnis
Werbung
Zeit bis zum automatischen
Ausschalten
Wenn die Geschwindigkeitsanzei-
ge OFF anzeigt, die Taste [ + ] / [ – ]
drücken, um einen Wert zwischen 1
Speed limit Setting
6.5.7
automatic off time
und 9 auszuwählen. Die Zahlen geben
die Minuten an, die bis zum automa-
When the speed field displays oFF, press
tischen Ausschalten des Displays
choose a figure between 1 and 9. the figures indicate
vergehen.
the minutes that it takes to automatically shut down
Danach kurz die Taste [ i ] drücken (<
the display.
0,3 Sekunden), um die Anzeige für die
After this setting, briefly press
Einstellung der Wartungshinweise zu
enter the setting interface of maintenance warning.
öffnen.
18
51
/
to
/
(< 0.3 seconds) to
"06"
6.6
error Code Definitions
"07"
AKKU-INFORMATIONEN
the MAX-C966 display can show e-bike faults. When a fa
Die Geschwindigkeitsanzeige zeigt
field one of the following error codes will be displayed:
"08"
b01 an und die Kilometeranzeige zeigt
die Geschwindigkeitsbegrenzung an.
6.5.12
Battery Communication
6.5.8
Maintenance Warning
Die Taste
Error Code
Error Description
"09"
the speed field displays b01 and the distance field
(can be deactivated)
[ i ] kurz drücken (< 0,3 Sekunden), um
nacheinander weitere Informationen
When the speed field displays nnA, press
displays the speed limit. Press
"03"
Brake enabled
anzeigen zu lassen. Danach die Taste
choose either 0 or 1. 0 disables the function while 1
to see the other information in sequence. After this
"11"
[ i ] zweimal hintereinander drücken
enables it.
setting, press
"04"
the throttle has not returned home
(< 0,3 Sekunden), um das Menü zu
After this setting, briefly press
menu.
verlassen.
enter the setting interface of password input.
"12"
"05"
throttle fault
• only when communication has been establis-
Folgende Informationen werden nur
hed between the battery and the controller the
angezeigt, wenn der Akku und die
"06"
Low voltage protection
"13"
Steuereinheit miteinander kommu-
following information will be displayed, otherwise
nizieren. Andernfalls erscheinen vier
the display will only show "- - - -".
"07"
overvoltage protection
Striche „- - - -".
"21"
"08"
Motor hall signal cable fault
"09"
Motor phase cable fault
"22"
"11"
Controller temperature sensor failure
"30"
"12"
Current sensor failure
"13"
Battery temperature fault
FEHLERCODES
"21"
Speed sensor fault
Das Display kann Fehler des E-Bikes
Maintenance Warning Setting
anzeigen. Nach dem Erkennen eines
"22"
BMS communication fault
the display will prompt maintenance necessity based
Fehlers wird das Symbol
on such information as the accumulated riding dis-
Kontaktieren Sie den Jumbo E-Bike
"30"
Communication fault
tance and the battery charge cycles.
Service.
• When the accumulated total riding distance
exceeds 5,000 km (can be customized by the
manufacturer), the display will show the symbol
. When the display is started up, the
Error display
sign for accumulated riding distance will flash
for 4 seconds, indicating that maintenance is
necessary.
• When the number of battery charge cycles ex-
55
ceeds 100 (can be customized by the manufactu-
Fehlerdisplay
Error display
rer), the display will the symbol
the display is started up, the sign for battery will
55
DEALER MAnuAL Max Drive SySteM
Low voltage protection
overvoltage protection
Motor hall signal cable f
Motor phase cable fault
(< 0.3 seconds)
Controller temperature s
twice (< 0.3 seconds) to exit the
(< 0.3 seconds) to
Current sensor failure
Battery temperature fau
Speed sensor fault
BMS communication fau
Communication fault
angezeigt.
/
to
. When
Werbung
Inhaltsverzeichnis
