Worcraft RH15-32X Gebrauchsanweisung Seite 43

plastic, a suitable SDS-Quick tool or an application tool with
hexagon shank can be used.
Inserting SDS-Quick Drilling Tools: Check the latching by
●
pulling the tool.
The maximum torque is reached only in the screwdriving
●
operating mode (1. gear). The maximum no-load speed is reached
only in the operating modes drilling and hammer drilling.
Replace a damaged dust protection cap immediately. The
●
dust protection cap largely prevents the penetration of drilling dust
into the tool holder during operation. When inserting the tool, pay
attention that the dust protection cap is not damaged.
Dust from materials such as lead-containing coatings, some
●
wood types, minerals and metal can be harmful to one's health
and cause allergic reactions, lead to respiratory infections
and/or cancer. Materials containing asbestos may only be worked
by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator. Observe
ASSEMBLY
Disconnect plug from the socket before making
any assembly, adjustments or changing accessories. Such
preventive safety measures reduce the risk of starting the tool
accidentally.
ASSEMBLE AUXILIARY HANDLE (Fig. 2).
Loosen the handle and put it through the chuck sleeve and move it
to the tool neck.
Fasten handle again to secure it in place.
The handle can be swiveled 360° by loosening and rotating.
To reposition and/or swivel the handle, loosen the hand grip, move
the handle to the desired position along the barrel and securely
retighten the hand grip.
OPERATION
SPEED SLECTOR （Fig.4）
This tool equipped 6 step speeds for working on different
conditions. Make sure to select right ones before operating.
SWITCHING ON/OFF （Fig.5）
To switching on the machine just press down the on/off switch.
To stop the tool, just relase the switch triiger.
DUST SHIELD （Fig.6）
When operation vertically upside, the concrete debris and dust will
fall down. The dust shield should be used for protect operators.
MODE SELECTOR （Fig. 7,8,9,10,11）
The selector knob allows the tool to be set for various
drilling/hammer, drilling or hammer applications.
Depress function shift button (5 & 6) and turn its' dial right or left
depending on the applications.
Drilling function: Trun front function knob(5) to the sign"
also turn the rear function knob(6) to the sign " ". See fig.8.
Hammer drilling function: Trun front function knob(5) to the sign"
", and also turn the rear function knob(6) to the sign "
fig.9.
Hammer function: Trun front function knob(5) to the sign"
MAINTENANCE
Make sure that the machine is not live when carrying out maintenance work on the motor. Regularly clean the machine
housing with a soft cloth, preferably after each use. Keep the ventilation slots free from dust and dirt. If the dirt does not come off
use a soft cloth moistened with soapy water. Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may
damage the plastic parts.
the relevant regulations in your country for the materials to
be worked.
Prevent dust accumulation at the workplace. Dust
●
can easily ignite.
If the application tool should become blocked,
●
switch the machine off. Loosen the application tool.
When switching on with a blocked drilling tool, high
●
torque reaction can occur.
Apply the power tool to the screw only when it is
●
switched off. Rotating tool inserts can slip off.
Always wait until the machine has come to a
●
complete stop before placing it down. The tool insert
can jam and lead to loss of control over the power tool.
To save energy, only switch the power tool on when using
●
it.
Avoid unintentional switching on. Ensure the On/Off
●
switch is in the off position before inserting battery
pack. Carrying the power tool with your finger on the
On/Off switch or inserting the battery pack into power tools
that have the switch on invites accidents.
INSTALLING AND REMOVE DRILL BITS (Fig.3.1 &3.2).
Clean the insert shank end of the drills or chisles to remove
any debris, then lightly grease with a light oil or lubricant
Insert drill bits or chisels into the chuck through the dust
shield, while twisting and pushing inward until it locks
automatically into place. Pull outward on the drill bits or
chisels to be certain it is locked into the chuck.
To remove the drill bits or chisels, pull locking sleeve
backward and pull bit forward. All accessories should be
wiped clean after removing.
Accessories may be hot after use. Avoid
contact with skin and use proper protective gloves or cloth to
remove.
also turn the rear function knob(6) to the sign "
fig.10.
Warning! DO NOT select combination function as "
" ". This will damage the tool. See fig.11.
Chisel angle free function: Trun front function knob(5)
upside. See fig. 12.
Do not operate the selection dial until the tool
comes to a complete stop. Shifting during rotation of the
chuck can cause damage to the tool.
When using demolition or chipping bits such as bull points,
chisels, spades, gouges, etc. the "Hammer Only" mode must
be selected.
SLIP CLUTCH
The tool has a internal pre-set slip clutch. The output spindle
will stop rotating if the accessory binds and overloads the
tool.
", and
CYLIDER / GEAR BOX LUBRICATION (Fig.12)
After long time operation, the tool need to make a regular
maintenance like lubrication, otherwise, its hammer force
". See
very possible becomes weak or disappear.
To lubricate the cylinder, just remove the plastic cover on top
", and
of the tool, and then add grease in it.
". See
" and