Panasonic TX-43MX700E Bedienungsanleitung Seite 20

Level and Signal Quality of the selected channel
will be shown. Press OK to start scan on the
selected RF channel. The found channels will be
stored in the channel list. You can press the Back/
Return button to cancel the scan. Then press the
Back/Return button again or highlight Finish and
press OK to exit.
Manual Service Update: Start a service update
manually. You can press OK or the Back/Return
button to cancel the scan. Then press OK or the
Back/Return button again to exit.
LCN: Set your preference for LCN. LCN is the Logical
Channel Number system that organises available
broadcasts in accordance with a recognisable
channel number sequence (if available).
Channel Scan Type: Set your scan type preference.
Channel Store Type: Set your store type prefe-
rence.
Favourite Network Select: Select your favourite
network. This menu option will be active, if more
than one network is available.
Cable
Channel Scan: Start a scan for digital cable
channels. If available, operator options will be
listed. Select the desired one and press OK. Scan
Mode, Frequency and Network ID options may be
available. The options may vary depending on the
operator and the Scan Mode selections. Set the
Scan Mode as Full if you don't know how to set up
other options. Highlight Scan and press OK or the
Right directional button to start the scan. You can
press the Back/Return button to cancel the scan.
The channels that have already been found will be
stored in the channel list.
Single RF Scan: Enter the Frequency value.
Signal Level and Signal Quality of the selected
Frequency will be shown. Highlight the Scan
option and press OK or the Right directional button
to start scan. The found channels will be stored in
the channel list.
LCN: Set your preference for LCN. LCN is the Logical
Channel Number system that organises available
broadcasts in accordance with a recognisable
channel number sequence (if available).
Channel Scan Type: Set your scan type preference.
Channel Store Type: Set your store type prefe-
rence.
Favourite Network Select: Select your favourite
network. This menu option will be active, if more
than one network is available. This option may not
be available depending on the selected country
during the initial setup process.
Satellite
Channel Installation Mode: Set this option as
Preferred Satellite or General Satellite. The
channel list will also change depending on the
selected option here. In order to watch the channels
on the satellite you want, this option should be
selected accordingly. Set to Preferred Satellite to
watch operator channels, if you have performed
an operator installation. Set to General Satellite
to watch other satellite channels, if you have
performed a normal installation.
Satellite Re-scan: Start a satellite scan beginning
with the antenna selection screen. When this
scanning option is preferred, some scanning
configurations will not be available and thus the
preferences you made during the initial setup
process may not be changed.
For the General Satellite channel installation mode
the SatcoDX Scan option may also be available
here. For standard installation select Normal
scan. For SatcoDX installation select SatcoDX
Scan and copy the relevant sdx file into the root
directory of an USB storage device and connect it
to your TV. Highlight this option and press OK or the
Right directional button. The Download SatcoDX
option will be highlighted, press OK or the Right
directional button to continue. Select the sdx file
from the connected USB storage device and press
OK. Satellite selection screen will be displayed. The
status of the first satellite option will appear as On.
Highlight that satellite option and press OK. Set
the parameters corresponding to your system and
correct satellite and press the Back/Return button
to return to the satellite selection screen. Highlight
Next and press OK to proceed with the SatcoDX
channel list installation. If the selected satellite is not
correct for SatcoDX installation, a warning dialogue
will be displayed on the screen. The satellite/s that
can be selected will be listed. Press OK to close the
dialogue and press OK or the Back/Return button
to return to satellite selection screen. Then set the
satellite accordingly.
Satellite Add: Add satellite/s on which you want
to perform a channel scan. This menu option will
be active, if Channel Installation Mode is set to
General Satellite.
Satellite Update: Search for any updates by
repeating the previous scan with the same settings.
You will also be able to configure these settings
before the scan. Depending on the Channel
Installation Mode setting, this option may not be
available or named differently depending on the
available services. Highlight the satellite and press
OK to configure detailed satellite parameters.
Then press the Back/Return button to return to
the satellite selection screen. Highlight Next and
press OK to proceed.
English - 19 -