Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
4.1. Function buttons
Button
Lock/
Light 1
Light 2
LED
unlock
On/Off
On/Off
On/Off
20
50
100
200
Lux
Lux
Lux
Lux
300
400
Learn actual lux
Lux
Lux
500
700
1000
No
Lux
Lux
Lux
Lux
Status
Status
Ch 1
Ch 2
Ch 1
Ch 2
Pulse
2min
5min
10min
Light 1
Light 2
LED
On/Off
On/Off
On/Off
8
15min
30min
60min
Hours
50
100
200
Test
Lux
Short
Lux
Long
Lux
Fact.
On/Off
push
push
setting
Light 2
LED
400
Learn actual lux
On/Off
On/Off
Lux
700
1000
No
100
200
Lux
Lux
Lux
Lux
Lux
Status
400
Status
Ch 2
actual lux
Ch 1
Lux
Ch 2
1000
No
2min
5min
10min
Lux
Lux
8
Status
Status
30min
60min
Hours
Ch 1
Ch 2
Short
Long
Fact.
5min
10min
push
push
setting
8
60min
Hours
Long
Fact.
push
setting
4.2. 'Set' buttons
To change the settings of the detector:
Lock/
Light 1
Light 2
LED
1. Press
three times within five seconds to unlock the device.
unlock
On/Off
On/Off
On/Off
20
50
100
200
The green indication LED flashes twice to confirm. The device is now in 'set' mode.
Lux
Lux
Lux
Lux
2. Change the light level or the switch-off delay using the buttons below.
300
400
Learn actual lux
Lux
Lux
Lock/
Light 1
Light 2
LED
500
700
1000
No
3. Press
once to lock the device again.
unlock
On/Off
On/Off
On/Off
Lux
Lux
Lux
Lux
Lock/
Light 1
Light 2
LED
unlock
On/Off
On/Off
On/Off
The green indication LED flashes twice to confirm. The modified setting is activated and the device will
20
50
100
200
Status
Status
Ch 1
Ch 2
Lux
Lux
Lux
Lux
Ch 1
Ch 2
return to the selected settings.
20
50
100
200
Lux
Lux
Lux
Lux
300
400
Pulse
2min
Learn actual lux
5min
10min
Lux
Lux
Note: If you do not lock the device, it will be locked automatically after two minutes. All changes will then
300
400
Learn actual lux
Lux
Lux
be saved automatically.
500
700
1000
No
8
15min
30min
60min
Lux
Lux
Lux
Hours
Lux
500
700
1000
No
Button
Lux
Lux
Lux
Lux
Test
Short
Status
Long
Status
Fact.
Ch 1
Ch 2
On/Off
push
push
Ch 1
setting
Ch 2
Status
Status
Ch 1
Ch 2
Ch 1
Ch 2
Pulse
2min
5min
10min
Pulse
2min
5min
10min
Lock/
Light 1
Light 2
LED
Lock/
Lock/
Light 1
Light 1
Light 2
Light 2
LED
LED
unlock
On/Off
On/Off
On/Off
Lock/
Light 1
Light 2
LED
unlock
unlock
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
8
unlock
On/Off
On/Off
On/Off
15min
30min
60min
Hours
8
15min
30min
60min
20
50
100
200
Hours
20
20
50
50
100
100
200
200
Lux
Lux
Lux
Lux
20
50
100
200
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Test
Short
Long
Fact.
Lux
Lux
Lux
Lux
On/Off
push
push
setting
Test
Short
Long
Fact.
300
400
Lock/
On/Off
Light 1
Light 2
push
push
LED
setting
Learn actual lux
300
300
400
400
Lux
Lux
unlock
On/Off
On/Off
Learn actual lux
Learn actual lux
On/Off
300
400
Lux
Lux
Lux
Lux
Learn actual lux
Lux
Lux
500
700
1000
No
20
50
100
200
500
500
700
700
1000
1000
No
No
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lux
500
700
1000
No
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Status
Status
300
400
Ch 1
Ch 2
Learn actual lux
Status
Status
Status
Status
Ch 1
Ch 2
Lux
Lux
Ch 1
Ch 1
Ch 2
Ch 2
Status
Status
Ch 1
Ch 1
Ch 2
Ch 2
Ch 1
Ch 2
Ch 1
Ch 2
500
700
1000
No
Lock/
Pulse
Light 1
2min
Light 2
5min
10min
LED
Lux
Pulse
Pulse
Lux
2min
2min
Lux
5min
5min
Lux
10min
10min
unlock
On/Off
On/Off
On/Off
Pulse
2min
5min
10min
8
Status
Status
15min
20
30min
50
60min
100
200
Ch 1
Ch 2
8
8
Hours
15min
15min
30min
30min
Ch 1
60min
60min
Ch 2
Lux
Lux
Lux
Lux
8
Hours
Hours
15min
30min
60min
Hours
Test
Short
Long
Fact.
300
400
Pulse
Test
Test
2min
Short
Short
5min
10min
Long
Long
Fact.
Fact.
On/Off
push
Learn actual lux
push
setting
Lock/
Light 1
Light 2
LED
Test
Lux
Short
Long
Fact.
Lux
On/Off
On/Off
push
push
push
push
setting
setting
unlock
On/Off
On/Off
On/Off
On/Off
push
push
setting
8
500
700
1000
No
15min
30min
60min
20
50
100
200
Hours
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Lux
Test
Short
Long
Fact.
Status
Status
Ch 1
Ch 2
On/Off
push
300
push
setting
400
Learn actual lux
Ch 1
Ch 2
Lux
Lux
Pulse
500
2min
700
1000
5min
10min
No
Lux
Lux
Lux
Lux
8
15min
30min
Status
60min
Status
Hours
Ch 1
Ch 2
Ch 1
Ch 2
Test
Short
Long
Fact.
On/Off
Pulse
2min
push
5min
push
setting
10min
8
15min
30min
60min
Hours
PM350-20078R23041
Test
Short
Long
Fact.
On/Off
push
push
setting
Function
You switch the light permanently on or off,
irrespective of the detected movement and the light level.
Lock/
Light 1
Light 2
LED
Briefly press
or follow the steps below
unlock
On/Off
On/Off
On/Off
Lock/
Light 1
Light 2
to activate this function:
unlock
On/Off
On/Off
20
50
100
200
Lux
Lux
Lux
Lux
Lock/
Light 1
Light 2
LED
20
50
100
1. Press
to switch the lighting on or off.
unlock
On/Off
On/Off
On/Off
Lux
Lux
Lux
300
400
Learn actual lux
Lux
Lux
If the function is activated, the red indication LED
20
50
100
200
300
Learn actual lux
Lux
Lux
Lux
Lux
Lux
will flash (1 s on, 10 s off).
500
700
1000
No
Lux
Lux
Lux
Lux
300
400
500
700
1000
Learn actual lux
Lux
Lux
Lux
Lux
Lux
Lock/
Light 1
Light 2
LED
2. Press
to switch the lighting on or off again.
unlock
On/Off
On/Off
On/Off
Status
Status
Ch 1
Ch 2
Ch 1
Ch 2
500
700
1000
No
Status
Ch 1
Ch 2
Lock/
Lux
Light 1
Lux
Light 2
Lux
LED
Lux
Ch 1
3. Press
20
50
again.
100
200
unlock
On/Off
On/Off
On/Off
Lux
Lux
Lux
Lux
Pulse
2min
5min
10min
Status
Status
Ch 1
Ch 2
Pulse
2min
5min
Ch 1
Ch 2
The detector will return to the selected settings. The
20
50
100
200
300
400
Lux
Lux
Learn actual lux
Lux
Lux
Lux
Lux
red indication LED will flash once to confirm.
8
15min
30min
60min
Hours
Pulse
2min
5min
10min
15min
30min
60min
300
400
You switch the indication LED on or off.
500
Learn actual lux
700
1000
No
Lux
Lux
Lux
Lux
Lux
Lux
Test
Short
Long
Fact.
On/Off
push
push
setting
8
Test
Short
Long
Lock/
15min
30min
60min
The indication LED will flash when
Hours
500
700
1000
On/Off
No
push
push
unlock
Status
Status
Ch 1
Lux
Ch 2
Lux
Lux
Lux
Ch 1
Ch 2
activated.
Test
Short
Long
Fact.
On/Off
push
push
setting
If you press this button, the device will show the current
Status
Status
Ch 1
Ch 2
Pulse
2min
Ch 1
5min
10min
Ch 2
settings for channel 1 via the indication LEDs.
Lock/
Light 1
Light 2
LED
unlock
On/Off
On/Off
On/Off
Pulse
2min
5min
10min
8
15min
30min
60min
Hours
First, the green indication LED flashes once, after which
20
50
100
200
the red indication LED indicates the status. The first time
Lux
Lux
Lux
Lux
8
15min
Test
30min
Short
60min
Long
Fact.
Hours
On/Off
push
push
setting
the red indication LED flashes, it indicates the lux level
300
400
you set; the second time, this LED refers to the switch-
Learn actual lux
Lux
Lux
Test
Short
Long
Fact.
On/Off
push
push
setting
off delay (see also the tables in section 3.3.).
500
700
1000
No
Lux
Lux
Lux
Lux
Pulse
Example: Channel 1 is set at 300 lux and 10 minutes.
Status
Status
Press
: the green indication LED flashes once and
Ch 1
Ch 2
Ch 1
Ch 2
15min
the red indication LED flashes five times (= 300 lux),
after which the green indication LED flashes once again
Pulse
2min
5min
10min
On/Off
and the red indication LED flashes four times (= 10 min).
8
15min
30min
60min
Hours
Test
Short
Long
Fact.
On/Off
push
push
setting
Function
Press this button to set the lux value and/or the
switch-off delay for channel 1.
The red indication LED indicates that you can adjust
the setting.
- With these red buttons, you set the desired light
level (lux value).
- There are ten fixed lux values: 20, 50, 100, 200,
300, 400, 500, 700 and 1000 lux and No lux
(daylight-independent).
- With this button, you set the current light level in
the room as the desired level at which the lighting
should be switched on.
- If you press this button, the red indication LED will
flash once to indicate that the current light level is
being saved. If this light level is not between 20 and
1000 lux, the minimum level (20 lux) or maximum
level (1000 lux) will be saved.
Use this setting if the desired minimum light level in
the room has been achieved. This is the point at which
the lighting should be switched on as the daylight
level is no longer sufficient.
- With these blue buttons, you set
the desired switch-off delay.
- There are six fixed values: 2, 5, 10, 15, 30 and 60
minutes.
Not applicable.
500
700
1000
No
Lux
Lux
Lux
Lux
Lock/
Light 1
Light 2
LED
unlock
On/Off
On/Off
On/Off
Status
Status
Ch 1
Ch 2
Ch 1
Ch 2
20
50
100
200
Lock/
Light 1
Light 2
Lux
Lux
Lux
Lux
unlock
On/Off
On/Off
Pulse
2min
5min
10min
300
400
Learn actual lux
20
50
100
Lux
Lux
Lux
Lux
Lux
8
15min
30min
60min
Hours
500
700
1000
No
300
Lux
Lux
Lux
Lux
Learn actual lux
Lux
Test
Short
Long
Fact.
On/Off
push
push
setting
Status
Status
Ch 1
Ch 2
500
700
1000
Ch 1
Ch 2
Lux
Lux
Lux
LED
Pulse
2min
5min
10min
Status
On/Off
Ch 1
Ch 2
Ch 1
8
200
15min
30min
60min
Hours
Lux
Pulse
2min
5min
Test
Short
Long
Fact.
400
On/Off
push
push
setting
Lux
15min
30min
60min
No
Test
Short
Long
Lux
On/Off
push
push
Status
Ch 2
10min
8
Hours
Fact.
Light 1
Light 2
LED
or
is
setting
On/Off
On/Off
On/Off
20
50
100
200
Lux
Lux
Lux
Lux
300
400
Learn actual lux
Lux
Lux
500
700
1000
No
Lux
Lux
Lux
Lux
Status
Status
Ch 1
Ch 2
Ch 1
Ch 2
5. OPERATION AND USE
2min
5min
10min
5.1. Activation
The detector should not be powered until all cables are connected. After powering the device, the detector will be
8
30min
60min
ready for use after approximately 120 seconds (warm-up time).
Hours
Test
Short
Long
Fact.
The red indication LED flashes during warm-up time. After the device has warmed up, the green indication LED
push
push
setting
will flash briefly twice.
5.2. General operation
The integrated light sensor continuously measures the daylight level in the detection area and compares this level
to the preset lux value. Thanks to the light sensor, the light switches on automatically only if the detector detects
motion within the detection range and if there is insufficient daylight:
• The lighting remains switched on as long as motion is detected and the amount of daylight
available in the room is insufficient.
• After the last motion is detected, the lighting remains switched on for the duration of the
preset switch-off delay (1 to 60 minutes). As soon as the switch-off delay has elapsed, the
lighting switches off.
• The lighting also switches off automatically as soon as the daylight level is sufficiently high,
even when motion is still detected in the room at that time.
5.3. Detection range
The detection area can be increased by adding an extra detector (secondary) (350-20079). A maximum of ten
secondary detectors can be connected to one master (350-20078). The lighting is operated in accordance with
the settings on the master. Both the master and the secondary detector have the same detection range (a circle
with a diameter of 24 m). When covering a complete area using several detectors, it is recommended to take into
account an overlap of approximately 30% (fig. 8).
If you would like to exclude motion detection in a portion of the detection area or if the detection area is too large,
you cover the sensor lens using the cover cap supplied. This allows you to reduce the maximum range to 24 m.
The 360° detection angle can be reduced in steps of 30°.
5.4. Examples of applications
Example 1: classroom
DIP switch 1
ON
OFF
How the presence detector works:
- The lighting is automatically switched on when the detector detects motion in the detection area and the
light level is less than the preset lux value.
- The lighting is automatically switched off again after a preset time (switch-off delay), provided that no
more motion is detected by the detector in the detection area or the light level has been higher than the preset
lux value for five minutes.
- The lighting can be switched on manually at any time by briefly pressing the push button. You can also
switch off the lighting manually (= eco off).
- In addition, you can also press and hold the push button, which is ideal for situations in which the lighting
should remain switched on (e.g. exam) or off (e.g. movie) for a longer period of time:
• By pressing and holding the push button while the lighting is switched on, the lighting will be
switched off. The detector will be locked for as long as activity is detected and the preset switch-off
delay + 2 hours has not yet elapsed. After that, the detector will return to the selected settings and the
lighting will be switched on.
• By pressing and holding the push button while the lighting is switched off, the lighting will be switched
on (irrespective of the daylight level). The lighting remains switched on for as long as activity is detected
LED
On/Off
Press this button:
200
Lux
- The lighting will be switched on
permanently for eight hours.
400
Lux
- Once the new setting has been confirmed (2 x
green led), the red led blinks (0,25 s on and 30 s
No
Lux
off).
Status
Ch 2
Press this button again to deactivate the function.
The red indication LED will no longer flash. You
10min
cannot switch off this function via a push button.
The device returns to the factory settings.
8
Hours
The detection area is tested by activating the
Fact.
setting
integrated motion sensor for the walking test:
- The blue indication LED lights up when you
activate the test mode.
- The lighting is switched on for five seconds and
the red indication LED lights up each time the
sensor detects activity.
- If no activity is detected and the sensor is still in
test mode, the blue indication LED lights up.
- If you forget to close the test mode, the detector
will return to the selected settings after five
minutes..
The light sensor does not work during the walking
test.
You can also activate the walking test via the
potentiometer for the switch-off delay.
DIP switch 3
DIP switch 4
x
x
x
350-20078
11
EN
Werbung
Inhaltsverzeichnis
