Herunterladen Inhalt Inhalt Diese Seite drucken

Turbo Button - Magic MGC HC 2 R Gebrauchsanleitung

Akku - haarschneideset
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 4
Fax +32 2 359 95 50
MOUNTING OF THE CUTTING ATTACHMENT (see Page 2 B )
To put the comb attachment on the clipper, insert it as described on page 2, B.
1)
2)
3)
To remove the comb attachment, proceed the other way round. (7)
Attachment # 0mm
Attachment # Tinning
Attachment #2mm
Attachment # 4mm
Attachment # 6mm
Attachment # Right Taper
Attachment # Left Taper
In order to make the use of the clipper easier, the blades can be put in 4 different directions. To
change the direction of the blades, hold the appliance with one hand and make the blade
support turn by 90° until you hear a click. The four different positions are always separated by a
90° angle.

TURBO BUTTON

The turbo button allows you to increase the motor speed instantaneously. This function is useful
if you have to cut thicker hair.
CUTTING HAIR WITH THE COMB ATTACHMENT (SEE PAGE 2: C)
We suggest you try the longest comb attachment on the clipper first in order to get used
to the different haircut heights. Choose a longer comb than the one you need, then
decrease the height until you reach the desired one. Only cut a small amount of hair to
start with until you become accustomed to the length the comb attachment gives to the
hair.
For uniform cutting, never push or force the clipper through the hair at a fast pace. The
clipper works most efficiently when it works at its own speed.
Once you've chosen the desired attachment, hold the clipper lightly against the hair with
the teeth of the comb attachment pointing up but flat against the head (8). Slowly lift the
clipper up and outward through the hair, cutting only a small amount at a time to avoid
the clipper to get stuck. To do so, regularly clear the attachment leaning it outwards. Do
the same movement but from a lower point than where you cleared the clipper, in order
to have a uniform haircut.
The haircut should be done by going the opposite way of the natural orientation of the
hair. For the back of the head, go from the nape to the top of the head (9). For the sides,
from the ears to the top of the head (10) and for the top of the head, go from the
forehead to the back of the skull (11).
We recommend you to regularly comb the hair in order to check the uniformity of the
haircut and to put the hair back in place. For the same reason, once the hair is cut and
combed, go once again with the clipper but faster, to cut hair that were not cut in the first
place. Insist on more difficult places.
If you feel the clipper doesn't cut and that the hair length is the same before and after you
used the clipper, check if no hair is stuck between the blades and the attachment. Remove the
attachment, put it back in place and try again. If necessary, decrease the haircut length.
Copies of the I/B. Please reproduce them without any
changes
except
International BELGIUM. The pages must be reproduced and
folded in order to obtain a booklet A5 (+/- 148.5 mm width x
210 mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don't change
the page numbering. Keep the language integrity.
Gently push on the side of the attachment.
Insert the plug of the attachment in the hole foreseen to that end on the
appliance.
Push gently on the sides of the attachment to fix it well.
Assembly page 11/48
under
special
instruction
protects when you cut short
Lets 1 mm of hair length
Lets 2 mm of hair length
Lets 4 mm of hair length
Lets 6 mm of hair length
To cut hair on the left side
To cut hair on the right side
11
from
Team
MGC HC 2 R - 080609

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis