Product Description And Specifications; Intended Use; Product Features; Technical Data - Bosch GWS 9-115 S Professional Originalbetriebsanleitung

18 | English
If the use of a guard is recommended for wire brush-
u
ing, do not allow any interference of the wire wheel or
brush with the guard. Wire wheel or brush may expand
in diameter due to work load and centrifugal forces.
Additional safety information
Wear safety goggles.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Release the On/Off switch and set it to the off position
u
when the power supply is interrupted, e. g., in case of
a power failure or when the mains plug is pulled. This
prevents uncontrolled restarting.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.

Technical Data

Angle grinder
Article number
Rated power input
Power output
Rated speed
Speed adjustment range
Max. grinding disc diameter
Grinding spindle thread
1 609 92A 6KB | (25.06.2021)
Please observe the illustrations at the beginning of this oper-
ating manual.

Intended use

The power tool is intended for cutting, roughing and brush-
ing metal and stone materials without the use of water.
A separate protective guard for cutting must be used when
cutting with bonded abrasives.
Sufficient dust extraction must be provided when cutting
stone.
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.

Product Features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Spindle lock button
(2) On/off switch
(3) Speed preselection thumbwheel
(4) Auxiliary handle (insulated gripping surface)
(5) Combination wrench for grinding spindle M 14
(6) Grinding spindle
(7) Unlocking lever for protective guard
(8) Protective guard for grinding
(9) Mounting flange with O‑ring
a)
(10) Grinding disc
(11) Clamping nut
(12) Quick-clamping nut
a)
(13) Carbide grinding head
(14) Protective guard for cutting
a)
(15) Cutting disc
a)
(16) Hand guard
a)
(17) Rubber sanding pad
a)
(18) Sanding sheet
a)
(19) Round nut
a)
(20) Cup brush
(21) Handle (insulated gripping surface)
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
GWS 9-115 S
3 601 C96 1..
W 900
W 450
-1
min 11,000
-1
min 2,800–11,000
mm 115
M 14
a)
a)
a)
GWS 9-125 S
3 601 C96 1..
900
450
11,000
2,800–11,000
125
M 14
Bosch Power Tools