EINHELL GE-SR 18/22 Li Originalbetriebsanleitung Seite 21

3. Risk of eye damage if essential safety gogg-
les are not worn.
5. Before starting the equipment
The machine is supplied without batteries
and without a charger!
Follow the instructions step by step and refer to
the pictures when assembling.
5.1 Fitting the wheels on the foot (Fig. 3-6)
Push a washer (Item 19), a wheel (Item 8) and
another washer (Item 19) onto the axle (Item
11a). Then press the straight part of the wheel
lock (Item 18) through the axle hole (Item 11b)
and secure the wheel. Fit the second wheel in the
same way.
5.2 Fitting the wheel caps (Fig. 7)
Place the wheel caps (Item 9) on the wheels (Item
8) so that the clips (Fig. 2/Item 9a) of the wheel
caps and the recesses (Fig. 2/Item 8a) of the
wheels are above each other. Press the wheel
caps onto the wheels.
5.3 Fitting the foot on the spreader material
compartment (Fig. 8)
Insert the foot tubes (Item 11b) in the mounts
(Item 7a) and fasten with the screws (Item 22).
5.4 Fitting the spacers on the long handle
tube (Fig. 9)
Important! Be sure to observe the correct align-
ment of the spacers (Item 13)! The cable guides
(Item 13b) must be on the right-hand side.
Push the spacers (Item 13) onto the two long
handle tubes (Item 4) and use the screws (Item
22) to secure to the respective long handle tube
(Item 4).
5.5 Fitting the long handle tubes on the
spreader material compartment
(Fig. 10-11)
Important! Be sure to observe the correct align-
ment of the screws!
Insert both long handle tubes (Item 4) in the tube
mounts (Item 7b) and secure with the M6 screws,
washers and cap nuts (Item 21).
Anl_GE_SR_18_22_Li_SPK13.indb 21 Anl_GE_SR_18_22_Li_SPK13.indb 21
GB
5.6 Fitting the handle on the long handle tube
(Fig. 12-13)
Insert the tube mounts (Item 1c) of the operating
unit into both long handle tubes (Item 4), place
the counterparts (Item 1b) on top, and use the
screws (Item 20) to secure them to the operating
unit (Item 1).
5.7 Connecting the Bowden wire (Fig. 14-16)
Screw together the lower part (Item 6a) and the
upper part (Item 6b) of the Bowden wire so that
they are fi rmly joined together. Align the Bowden
wire (Item 6) and the connecting line (Item 5) so
that they are inside the cable guides (Fig. 9/Item
13b).
5.8 Fitting the battery (Fig. 17)
Note: The battery compartment cover is self-
closing and is held shut by magnets.
Inserting: Open the battery compartment cover
(Item 16) and insert the battery in the battery
mount.
Removing: Open the battery compartment cover
(Item 16), press the battery pushlock button (Item
C) and pull out the battery.
5.9 Charging the battery (Fig. 18)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Insert the battery pack into the battery char-
ger.
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
- 21 -
16.11.2023 09:05:01 16.11.2023 09:05:01